Samsung DVR SHR 2040 User Guide
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page i  
Real Time DVR  
SHR-2040/2041/2042 User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page iii  
Be fo re w e sta rt  
This User’s Manual describes the basic usage of SHR-2040/2041/2042. This Manual  
contains all the matters necessary for using SHR-2040/2041/2042 such as brief  
instruction, part name, function, connecting other equipment, and menu setup of  
SHR-2040/2041/2042.  
-
-
-
SEC retains the copyright on this User’s Manual.  
This User’s Manual cannot be copied without SEC’s prior written approval.  
We are not liable for any or all losses to the product incurred by your use of non-  
standard product or violation of User’s Manual.  
-
-
If you want to open the system case to touch the inside, please consult with an  
expert who works for the shop where you bought the product.  
You may download open source codes from the following website.  
(See CCTV Part of http://www.sec.co.kr)  
WARNING  
[Battery]  
As wrong exchange of the battery in SHR-2040/2041/2042 may cause explosion, you  
shall use the certified battery for SHR-2040/2041/2042.  
The battery specification is as follows.  
-Normal Voltage: 3V  
-Normal Capacity: 220mAh  
-Continuous Standard Load: 0.2mA  
-Operating Temperature: -30 ~ +60˚C  
[System Shutdown]  
- Power-off without terminating the system in the System Shutdown menu may incur  
improper motion like data loss and disk failure. Power-off shall be done in the  
System Shutdown menu.  
Standards Approvals  
Note : This equipment has been tested and found to comply with the limits for a Class  
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance whit the instruction manual, may cause  
harmful interference to radio communications. Operation of this equipment in a  
residential area is likely to cause harmful interference in which case the user  
will be required to correct the interference at his own expense.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page iv  
Co n te n ts  
Safety Regulations  
ii  
Before w e start  
iii  
Standards Approvals  
Chapter 1 Overview  
1. Introduction  
1
1-1  
1-2  
1-3  
2. Features  
3. Part Names and Functions  
Chapter 2 Installation  
2
1. Installation Environment Setup  
2. Checking Product & Accessory  
3. HDD Addition  
2-1  
2-2  
2-3  
3
Chapter 3 Connecting w ith Other device  
1. Connecting Video, Audio, & Monitor  
2. Connecting the Network  
3-1  
3-3  
3-5  
3-6  
3-8  
3. Connecting the USB  
4. Connecting the Alarm Input/Output  
5. Connecting the RS-485 Device  
4
Chapter 4 Live  
1. System Operation  
4-1  
4-2  
4-5  
4-6  
4-7  
4-8  
2. Live Screen Mode  
3. Live Channel Selection and Audio On/Off Setup  
4. Freeze and Zoom  
5. Event Monitoring  
6. Spot-out Monitoring  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page v  
Chapter 5 Menu Setup  
5
Before Use  
5-1  
5-2  
1. System  
2. Camera  
5-12  
5-16  
5-18  
5-20  
5-25  
5-27  
5-28  
5-32  
3. Monitoring  
4. Recording Mode  
5. Event Record Mode  
6. Record Schedule  
7. Backup  
8. Network  
9. Network Setup  
Chapter 6 PTZ Cam era Control  
1. PTZ camera Control Mode  
2. Basic Operation of PAN, TILT, & ZOOM  
3. Preset Setup  
6
6-1  
6-3  
6-4  
6-6  
6-7  
6-8  
4. Camera Menu Setup  
5. Preset View  
6. Other View  
Chapter 7 Recording  
7
1. REC (Normal Recording)  
2. Schedule Recording  
3. Event Recording  
7-1  
7-2  
7-3  
Chapter 8 Search and Play  
Before Use  
8
8-1  
8-2  
8-3  
8-4  
8-5  
8-6  
8-7  
8-8  
1. Calendar Search  
2. Event Search  
3. Date/Time Search  
4. Go to First Search  
5. Go to Last Search  
6. Backup  
7. Playback  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page vi  
Chapter 9 Sm art View er  
9
9-1  
9-2  
9-3  
9-4  
9-7  
9-8  
9-9  
9-23  
9-30  
1. Introduction  
2. Feature  
3. PC Specification(Recommendation)  
4. Smart Viewer Installation  
5. Smart Viewer Program Execution  
6. Smart Viewer Initial Screen  
7. Monitoring Mode  
8. Search Mode  
9. Setup Mode  
Appendix  
10  
1. Product Specification  
10-1  
10-4  
10-5  
10-7  
10-9  
10-11  
2. The specification of HDD and peripheral device  
3. Outline Drawings  
4. Factory Default  
5. Smart Viewer Frame Specification for the Playback  
6. Troubleshooting(FAQ)  
vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1  
Ch a p te r 1 O ve rvie w  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-1  
SHR-2040/2041/2042 USER’S MANUAL  
In tro d u ctio n  
1
The Digital Video Recorder(DVR) compresses the 4 channel of camera input data into the  
MPEG4 video file and the 4 channel of voice input data into the ADPCM audio file in the real  
time to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously.  
In addition, it transfers the Video/Audio out through a network in the real time and it is able to  
monitor the Video/Audio remotely by your PC.  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-2  
Fe a tu re s  
2
■
■
4 CH Composite Input Connectors  
NTSC / PAL Video Source Compatible  
( NTSC : SHR-2040/SHR-2041/SHR2042, SHR-2040N / SHR-2041N / SHR-2042N  
PAL : SHR-2040P/SHR-2041P/SHR2042P)  
■
Able to record the CIF sized (NTSC-352 x 240/PAL-352 x 288) video at the speed of  
120 ips(NTSC)/100ips(PAL)(Image Per Second)  
4 CH Loop Through Video Connectors  
■
■
■
■
Hard Disk Overwrite Mode  
Large Quantity Hard Disk Backup by USB2.0  
Backup function by the USB2.0 memory and exterior CD/DVD writer(SHR-2042 supports  
the internal CD-RW.)  
■
Able to record, play, and transmit both audio and video files to Windows Network  
Viewer(Smart Viewer) simultaneously  
■
■
■
■
■
■
Able to record and play the audio 4CH  
Variable Search Mode (Time/Date, Event, Camera)  
Variable Recording Mode (Time Lapse, Event, Schedule)  
Extended Hard Disk Connection (USB2.0)  
Alarm Interface function (Input : 4, Output:2, Reset:1)  
Remote Monitoring function by Windows Network Viewer(Smart Viewer)  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-3  
SHR-2040/2041/2042 USER’S MANUAL  
Pa rt N a m e s a n d Fu n ctio n s  
3
[SHR-2040]  
No.  
Name  
Power LED  
Function  
Displays power on/off condition.  
lights on when an event occurs.  
Alarm LED  
Displays Normal Access to HDD. Upon Access to HDD, LED  
repeats on and off.  
HDD Access  
LED  
1
Displays both network connection and data transmission conditions.  
Displays Back Up Mode.  
Network LED  
Backup LED  
Displays the record condition.  
Rec LED  
1
4
Selects a channel in the Single Mode. Used for number  
input button in the number input mode.  
2
3
4
Channel Button  
...  
AUDIO  
Audio Setup  
Button  
Sets the Audio On/Off.  
ALARM  
Audio Setup  
Button  
Cancels the alarm when the Alarm button is selected.  
Displays 4 split screen.  
MODE  
Displays PIP(Picture in Picture) screen.  
Split Screen  
Display  
5
Selection Button  
Mode  
The single channel screen is changed  
according to the time set on the menu.  
Displays 4 split screen.  
Displays both LIVE Channel and Playback  
Channel in the PIP Screen simultaneously.  
MODE  
Mode Selection  
Button  
6
Search  
Displays 6 split screen.  
(1 CH playback screen and 4 CH live screen)  
Displays 9 split screen.  
(4 CH playback screen and 4 CH live screen)  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-4  
No.  
Name  
PTZ Button  
Function  
PTZ  
Performs the TELE, WIDE, PRESET, and VIEW function.  
7
ZOOM  
ZOOM(TELE)  
Button  
Sets up Digital Zoom(x2).  
8
9
( Performs the TELE function by pressing the PTZ button.)  
TELE  
FREEZE  
Performs the FREEZE function in the DISPLAY Mode.  
( Performs the WIDE function by pressing the PTZ button.)  
FREEZE(WIDE)  
Button  
WIDE  
SEARCH  
Displays the search method.  
SEARCH(VIEW)  
Button  
10  
( Performs the VIEW function by pressing the PTZ button.)  
VIEW  
MENU  
Displays the system setup menu or enters to the upper  
menu.( Performs the PRESET setup function by pressing  
the PTZ.)  
MENU (PRESET)  
Button  
11  
12  
PRESET  
Records the record setup set in the normal record mode.  
RECORD  
Fast Reverse: Used for the fast rewinding  
Fast/Step  
Reverse  
search in the playback mode.  
Step Reverse: Used for the 1 step reverse  
search during the pause.  
13  
STOP  
14  
15  
Used for the search stop in the playback mode.  
Search Function  
Key  
Toggles in the playback mode to activate  
PLAY/PAUSE.  
PLAY/PAUSE  
Fast Forward: Used for the fast-forwarding  
search in the playback mode.  
Step Forward: Used for the 1 step-forwarding  
search during the pause.  
Fast/Step  
Forward  
16  
In case of setting the details of Menu, it is  
used as Direction Key. (For PTZ Operation)  
¦
œ
‹
In case of setting the details of Menu, it  
increases the value or it is used as Direction  
Key. (For PTZ Operation)  
In case of setting the details of Menu, it is  
used as Direction Key. (For PTZ Operation)  
Direction Button  
Key  
17  
18  
In case of setting the details of Menu, it  
decreases the value or it is used as Direction  
Key. (For PTZ Operation)  
ƒ
Acts as the Enter key for the menu setup.  
¦
Connects the USB type device.  
USB Port  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-5  
SHR-2040/2041/2042 USER’S MANUAL  
[SHR-2041]  
[SHR-2042]  
No.  
Name  
Power LED  
Function  
Displays power on/off condition.  
lights on when an event occurs.  
Alarm LED  
Displays Normal Access to HDD. Upon Access to HDD, LED  
repeats on and off.  
HDD Access  
LED  
1
Displays both network connection and data transmission conditions.  
Displays Back Up Mode.  
Network LED  
Backup LED  
Rec LED  
Displays the record condition.  
2
3
4
Performs the OPEN/CLOSE of CD/RW.  
Eject Button  
1
4
Selects a channel in the Single Mode. Used for number  
input button in the number input mode.  
Channel Button  
...  
AUDIO  
Audio Setup  
Button  
Sets the Audio On/Off.  
ALARM  
Alarm Setup  
Button  
Cancels the alarm when the Alarm button is selected.  
Displays 4 split screen.  
5
6
MODE  
Split Screen  
Selection Button  
Display  
Mode  
Displays PIP(Picture in Picture) screen.  
Auto Sequence Mode: The single channel screen  
is changed according to the time set on the menu.  
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-6  
No.  
Name  
Function  
Displays 4 split screen.  
Displays the selected channel to the Single Mode  
Displays both LIVE Channel and Playback  
Channel in the PIP Screen simultaneously.  
MODE  
Mode Selection  
Search  
7
Displays 6 split screen.  
(1 CH playback screen and 4 CH live screen)  
Button  
Displays 9 split screen.  
(4 CH playback screen and 4 CH live screen)  
PTZ  
PTZ Button  
Performs the TELE, WIDE, PRESET, and VIEW function.  
8
9
ZOOM  
Sets up Digital Zoom(x2).  
ZOOM(TELE)  
Button  
( Performs the TELE function by pressing the PTZ button.)  
TELE  
FREEZE  
Performs the FREEZE function in the DISPLAY Mode.  
( Performs the WIDE function by pressing the PTZ button.)  
FREEZE(WIDE)  
Button  
10  
11  
WIDE  
SEARCH  
Displays the search method.( Performs the VIEW function  
by pressing the PTZ button.)  
SEARCH(VIEW)  
Button  
VIEW  
MENU  
Displays the system setup menu or enters to the upper  
menu.( Performs the PRESET setup function by pressing  
the PTZ.)  
MENU (PRESET)  
Button  
12  
13  
PRESET  
Records the record setup set in the normal record mode.  
Fast Reverse: Used for the fast rewinding  
RECORD  
Fast/Step  
Reverse  
search in the playback mode.  
Step Reverse: Used for the 1 step reverse  
search during the pause.  
14  
Used for the search stop in the playback mode.  
15  
16  
STOP  
Search Function  
Key  
Toggles in the playback mode to activate  
PLAY/PAUSE.  
PLAY/PAUSE  
Fast Forward: Used for the fast-forwarding  
search in the playback mode.  
Step Forward: Used for the 1 step-forwarding  
search during the pause.  
Fast / Step  
Forward  
17  
In case of setting the details of Menu, it is  
used as Direction Key. (For PTZ Operation)  
¦
œ
‹
In case of setting the details of Menu, it  
increases the value or it is used as  
Direction Key. (For PTZ Operation)  
Direction Button  
Key  
In case of setting the details of Menu, it is  
used as Direction Key. (For PTZ Operation)  
18  
19  
In case of setting the details of Menu, it  
decreases the value or it is used as  
Direction Key. (For PTZ Operation)  
ƒ
Acts as the Enter key for the menu setup.  
¦
Connects the USB type device.  
USB Port  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-7  
SHR-2040/2041/2042 USER’S MANUAL  
[SHR-2040]  
Caution  
Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator.  
To play DVR on the cabinet or rack, be sure to check the ventilation condition.  
No.  
Name  
Function  
1
Composite Video Signal Input Port (BNC Style Connector)  
VIDEO IN  
You may use THROUGH port to transmit a video signal to the  
other video equipment.  
THROUGH  
2
3
Audio Signal Input Port (RCA Jack)  
AUDIO IN  
4
5
AUDIO OUT  
Audio Signal Output Port (RCA Jack)  
Composite Video Signal Output Port (BNC Style Connector)  
VIDEO OUT  
VGA Video Signal Output Port  
VGA  
6
7
S-VIDEO  
SPOT OUT  
S-VIDEO Video Signal Output Port  
SPOT Out Output Port (BNC Style Connector)  
8
- ALARM IN 1~4 : Alarm Input Port  
- ALARM RESET IN : Alarm Reset Port  
- ALARM OUT1~2 : Alarm Output Port  
- TX+, TX-, RX+, RX- : RS-485 Communication  
ALARM  
9
10  
11  
12  
USB  
NETWORK  
DC-IN  
USB connection Port  
Network Connection Port  
12V Power Socket Support  
1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-8  
[SHR-2041/2042]  
Caution  
Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator.  
To play DVR on the cabinet or rack, be sure to check the ventilation condition.  
No.  
Name  
Function  
1
VIDEO IN  
Composite Video Signal Input Port (BNC Style Connector)  
You may use THROUGH port to transmit a video signal to the  
other video equipment.  
THROUGH  
2
3
Audio Signal Input Port (RCA Jack)  
AUDIO IN  
4
5
AUDIO OUT  
Audio Signal Output Port (RCA Jack)  
Composite Video Signal Output Port (BNC Style Connector)  
VIDEO OUT  
VGA Video Signal Output Port  
VGA  
6
7
S-VIDEO  
SPOT OUT  
S-VIDEO Video Signal Output Port  
SPOT Out Output Port (BNC Style Connector)  
8
- ALARM IN 1~4 : Alarm Input Port  
- ALARM RESET IN : Alarm Reset Port  
- ALARM OUT1~2 : Alarm Output Port  
- TX+, TX-, RX+, RX- : RS-485 Communication  
ALARM  
9
USB connection Port  
10  
11  
12  
USB  
NETWORK  
AC-IN  
Network Connection Port  
(NTSC) AC 100~230V Power Socket Support  
(PAL) AC 100~230V Power Socket Support  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3  
Ch a p te r 2 In sta lla tio n  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-1  
SHR-2040/2041/2042 USER’S MANUAL  
In sta lla tio n En viro n m e n t Se tu p  
1
Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator.  
To play DVR on the cabinet or rack, be sure to check the ventilation condition.  
You should pay attention to the following before you use the product.  
1. Do not use it outdoor.  
2. Do not let water or liquid in the connection part or the product itself.  
3. Do not impose excessive shock or force.  
4. Do not pull out the power plug unreasonably.  
5. Do not disassemble the product on your own.  
6. Do not exceed the rated input or output range.  
7. Use certified power cord only.  
8. Use the power cord with a ground for the product with an input ground.  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-2  
Ch e ck in g Pro d u ct & Acce sso ry  
2
Upon delivery of a product, you shall unwrap the product and put it on the even floor or where  
you want to use it. Then you shall check if the following items are in it.  
■ Main Body  
■ User’s Manual  
■ One Power Cord  
■ Two Brackets  
- These are not supplied in SHR-2040.  
- Brackets are used to attach the product to the rack.  
■ Smart Viewer Software CD (PDF Manual included)  
■ Special Screws  
- Please keep special screws well to be used for HDD addition.  
- These are not supplied in SHR2040.  
■ 2 EA of RS-485/Alarm Terminal Block  
Main Body  
SHR-2040  
Main Body  
SHR-2041  
Main Body  
SHR-2042  
CD  
Bracket  
Power Cord  
RS-485/Alarm  
Terminal Block  
Adapter  
(Only 2040)  
User’s Manual  
Screw  
WARNING) SHR-2040 set must use the adapter we provide.  
Adapter: ADP-5412WD  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-3  
SHR-2040/2041/2042 USER’S MANUAL  
HDD Ad d itio n  
3
You can add up HDD to the product.(2040-1 HDD/2041-3 HDDs/2042-2 HDDs)  
However, since the product contains has many parts which may incur electric shock,  
accident, or product breakdown and improper installation or setup may disturb HDD  
recognition or normal product operation, you shall consult with an expert of the agency  
where you bought the product.  
[Caution for HDD Addition]  
■ Do not let the cable stuck improperly nor uncoated. (This may cause breakdown or fire.)  
■ Be careful not to hurt yourself by sharp edges of the product.  
■ Be careful not to miss the disassembled screws or parts. Imperfect assembly due to short of  
screws or parts may cause breakdown or malfunctioning.  
[HDD Addition Procedure]  
1. Loosen screws on both sides(5 points) and back(1 point) to detach the product cover.  
[SHR-2040]  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-4  
[SHR-2041]  
[SHR-2042]  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-5  
SHR-2040/2041/2042 USER’S MANUAL  
2. Detach the cover from the product. (Pull out the cover slightly and lift from the back side to  
detach.)  
[SHR-2040]  
[SHR-2041/2042]  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-6  
3. A bracket(BRACKET- HDD) is mounted to each side of product to fix the HDD. Please loosen  
the screw of the bracket to which you want to fix HDD.  
BRACKET-HDD  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-7  
SHR-2040/2041/2042 USER’S MANUAL  
4. Pull BRACKET-HDD to the product center to detach the fixed part at the bottom and detach  
BRACKET-HDD from the product.  
5. Tighten 4 special screws(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to  
BRACKET-HDD. (A force to tighten the screw shall be strong enough to resist vibration.)  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-8  
6. Reattach HDD to the original position of BRACKET-HDD.  
(Assembly shall be done in the reverse procedure of disassembly as follows. Align the 5  
fixing points at the bottom with the BRACKET-HDD fixing holes respectively and push  
BRACKET-HDD out of the product to align the screw fixing holes. Then, tighten the screws  
firmly.)  
7. Check if BRACKET-HDD has been fixed to the product and connect both the power supply  
cable and the signal transmission cable (IDE CABLE) to the HDD.  
Power Supply Cable  
Signal Transmission Cable  
(IDE Cable)  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-9  
SHR-2040/2041/2042 USER’S MANUAL  
8. Check the connector, wiring, and cable fixing condition inside the product and close the  
cover.  
9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side)  
■ You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.  
Caution  
For HDD addition, please select the same HDD with the existing HDD fixed to the product as  
far as possible.  
- SHR-2040 : 1 at Primary Slot and 1 at Secondary Slot respectively  
- SHR-2041 : 2 at Primary Slot and 2 at Secondary Slot respectively  
- SHR-2042 : 2 at Primary Slot and 1 at Secondary Slot(The internal CD-RW is connected to  
the secondary master.) respectively  
Both HDDs attached to Primary Slot and Secondary Slot should be set to Master and Slave  
respectively. Refer to User’s Manual for Master or Slave Jumper Setting.  
In the event of only one HDD installation, it shall be inserted into the Primary slot.  
Note  
Refer to Appendix 2 to see which HDD specifications are supplied.  
2-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-10  
WARNING  
! Regarding the sub fan, you need additional brackets and sub fans as follows.  
The sub fan is shaped like this when viewed from the front and back. Please pay attention to  
the fan direction to let wind go through the fan.  
@ Fix the fan as follows  
2-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-11  
SHR-2040/2041/2042 USER’S MANUAL  
# Please install the fan which is seen at the right from the front view of SHR-set as follows.  
2-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-12  
$ The cable should be out from the left hole.  
2-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3  
Ch a p te r 3 Co n n e ctin g  
w ith o th e r d e vice  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-1  
SHR-2040/2041/2042 USER’S MANUAL  
Connecting the Video, Audio, a nd Monitor  
1
[SHR-2040]  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-2  
[SHR-2041/2042]  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-3  
SHR-2040/2041/2042 USER’S MANUAL  
Co n n e ctin g th e N e tw o rk  
2
■
Connecting to Internet through Ethernet(10/100BaseT)  
[SHR-2040]  
■
Connecting to Internet through ADSL  
[SHR-2040]  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-4  
■
Connecting to Internet through Ethernet(10/100BaseT)  
[SHR-2041/2042]  
■
Connecting to Internet through ADSL  
[SHR-2041/2042]  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-5  
SHR-2040/2041/2042 USER’S MANUAL  
Co n n e ctin g th e USB  
3
1. There are two USB connecting ports on the front and back of SHR-2040/2041/2042.  
2. USB Hard Disk, USB CD/DVD, and USB Memory are connected through the front and back  
ports of SHR-2040/2041/2042.  
3. Only one USB device can be connected with each USB connecting port.  
4. If the USB HDD is connected to the system, it should be detected and set through  
Menu - System - HDD setup before the operation.  
5. It supplies the function of HOT PLUG, which connects/removes the USB device, during the  
system operation.  
Note  
See 5-8 System (HDD Setup) of User’s Manual.  
Caution  
- Wait until the USB device connected by hot plug is stabilized enough and click CONNECT  
in SHR-2040 / 2041 / 2042 MENU before use.  
- USB port on the front and back of SHR-2040/2041/2042 cannot be connected to same kinds  
of USB device. (For example, the case is that 2 CD-RW devices or 2 USB Memories are used  
by connection with the front and back of system.)  
- If you use the USB Memory on SHR-2040/2041/2042, it should be composed of the format  
being supported by SHR-2040/2041/2042. Although you format it with FAT32 format on PC,  
it will be re-formatted, in case of (when) connecting with SHR- 2040/2041/2042.  
Caution  
- The hard disk of USB device should be set to Master.  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-6  
Co n n e ctin g th e Ala rm In p u t/ O u tp u t  
4
The Alarm IN/OUT port in the back of SHR-2040/2041/2042 is composed of the following  
elements.  
■
ALARM IN/OUT Connection  
Name  
Function  
- ALARM IN1  
1
- ALARM IN2  
- ALARM IN3  
- ALARM IN4  
ALARM Input Port  
On receiving an ALARM RESET signal, the sys-  
tem cancels the current ALARM input and output  
signal and then resumes sensing.  
2
3
- ALARM RESET IN  
- ALARM OUT1  
- ALARM OUT2  
ALARM Output Port  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-7  
SHR-2040/2041/2042 USER’S MANUAL  
■
ALARM IN/OUT Connection  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-8  
Co n n e ctin g th e RS-4 8 5 De vice  
5
■
Connect the RS-485 Device through the back port of SHR- SHR-2040/2041/2042.  
You can install and control the PTZ camera supporting the RS-485 communication.  
■
■
You can adopt either Half Duplex or Full Duplex method for the connection.  
PTZ device  
SHR-2040/2041/2042  
Rear  
Half Duplex Type  
Data (–)  
Data (+)  
Tx(–)  
Tx(+)  
Full Duplex Type  
Rx(+)  
Rx(–)  
Tx(–)  
Tx(+)  
Rx(–)  
Rx(+)  
■
Baud Rate supports 600/1200/2400/4800/9600/19200/38400.  
Caution  
Check if RS-485 device is compatible with SHR-2040/2041/2042 first. Then pay attention not  
to change the polarity(+, -) of RS-485 when connecting it.  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5  
Ch a p te r 4 Live  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-1  
SHR-2040/2041/2042 USER’S MANUAL  
Sy ste m O p e ra tio n  
1
■
Turn the power on and the following LOGO pops up on the screen.  
■
■
■
After the LOGO appears, all of LED in the front flickers 6 times to initialize the system for  
operation.  
Upon completion of normal initialization, the Live screen appears accompanying a beep  
sound.  
It requires 30 to 40 seconds until the Live screen appears.  
Note  
If a new HDD is installed, it may require more time to be appeared the Live screen due to the  
initialization time of a new HDD.  
If the Live screen does not appear continuously or the LED in front repeats flickering, please  
check the connection between inside and outside. If the system does not operate in normal,  
contact with the shop where you bought the product.  
■
The Live screen does not affect the earlier MENU setup. If you reboot the system  
after power-off during recording, the Live screen will appear, accompanying recording.  
Note  
If the Live screen dose not appear, check if the Video Out comes out in Composite mode or  
VGA mode.  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-2  
Live scre e n Mo d e  
2
Definition of Live Screen Icon  
The Live screen icons display the current setup and function status of each screen.  
PTZ  
N
V.Loss  
CAM_01  
CAM_01  
: Recording Icon  
P
E
S
Each icon represents Normal / Event (Alarm + Motion) / Schedule Recording.  
Recording Video Size Icon  
Each icon represents the recording size of Large / Normal / CIF.  
- Large : Full D1 - (NTSC) 720X480 (PAL) 720X576  
- Normal : Half D1 - (NTSC)720X240 (PAL) 720X288  
- CIF  
: CIF - (NTSC)352X240 (PAL)352X288  
(Full D1 is supported only when “1 CH DVR support”)  
PTZ  
: PTZ Icon  
This icon appears when setting the PTZ device with the PTZ icon and changes to yellow color  
when operating the PTZ.  
: Audio Icon  
This icon represents the Audio On/Off status and changes to yellow color at the Audio On. It  
does not appear in the Video mode or Audio Disable.  
: Sensor In Event Icon  
This icon appears in the channel linked with the external sensor signal when inputting the signal  
at the Sensor On.  
: Motion Event Icon  
This icon appears in the Motion Event channel at the Motion Detection On.  
: Zoom Icon  
This icon appears at the Zoom On or Zoom In and disappears when canceling the Zoom On.  
: Freeze Icon  
This icon appears in the Freeze mode and disappears when canceling the Freeze.  
HDD Recording Disk Full Icon  
This icon appears when the recording space is full in the HDD.  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-3  
SHR-2040/2041/2042 USER’S MANUAL  
: Auto sequence Icon  
This icon appears in the auto sequence mode.  
: Backup Playback Icon  
This icon appears when the backup data is played.  
: Fan Error Icon  
This icon appears when the fan stops.  
: This icon appears when there is no HDD.  
V.Loss / V.Off : Video Input Status  
If there is no more video data input in the Video On, [V.Loss] appears in the channel.  
If you set Video On/Off to Off, [V.Off] will appear.  
Definition of Live Screen Mode  
The system receives 3 live images and displays them in the following 3 modes.  
CAM_01  
CAM_02  
■
■
CAM_02  
CAM_01  
CAM_03  
CAM_04  
4 Split Mode  
PIP Mode  
Auto sequence Mode  
■
■
4 Split Mode:  
Four channels are split in the screen separately.  
You are able to choose a channel as you want to in each split mode.  
PIP(Picture In Picture) Mode:  
Displays a one-fourth sized screen in the full screen. You are able to choose a channel as  
you want to, which is displayed in the full screen and reduced screen area. You may move  
the PIP screen at 5 stages in the Full screen with the œ,ƒ¤key.  
■
Auto sequence Mode:  
Displays the full screen of each channel in sequence according to the setup time.  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-4  
Selecting Live Screen Mode  
Each mode may be selected by [MODE Button] and [CH1 ~ CH4 Button].  
The following figure shows Live Mode after converted.  
■
■
The default setup is 4 Split Screen Mode.  
You are able to choose other modes than Full Screen Mode by the [MODE] button in  
sequence. Whenever you press the [MODE] button, the system will change  
[4Split]■[PIP]■[auto sequence]■[4 Split] in sequence.  
■
■
If you press [CH1~CH4 button], you will be able to see the full screen of each channel.  
The MODE button is used to return to the previous split mode screen from a full screen  
mode.  
4-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-5  
SHR-2040/2041/2042 USER’S MANUAL  
Live Cha nnel Selection a nd Audio On/ Off Setup  
3
In other split modes than Full Screen Mode and Auto Sequence Mode, you can choose a channel  
to be displayed in each split area on your own. In addition, the channel being set to Audio On can  
be set to Audio On/Off in all Live Modes.  
Audio On/Off Setup in the Full Screen  
In the Full Screen Mode, the selected channel Audio is automatically turned on and you can set  
up Audio On/Off with toggling the channel button. Depending on the Audio On/Off setup  
condition, the Audio icon of the channel changes to the Yellow/white color.  
Audio On/Off Setup in the 4 Split Mode  
If you press [ENTER] Button in the 4 Split Mode, the selection cursor in the following figure  
will appear and the channel concerned will be selected. If you press the Audio button in the status  
of being selected a channel, you can set Audio On/Off for the channel concerned. Depending on  
the Audio On/Off setup condition, the Audio icon of the channel changes to the Yellow/white color.  
CAM_01  
CAM_03  
CAM_02  
CAM_04  
Channel Selection and Audio On/Off Setup in the PIP Mode  
As in the 4 Split Mode, if you press [ENTER] button in the PIP Mode, the selection cursor appears  
and the concerned channel is selected. With being selected a channel, you can select a channel  
on the current screen by the [CH1 ~ CH4] button and set Audio On/Off by the Audio button as in  
the 4 Split Mode. Depending on the Audio On/Off setup condition, the Audio icon of the channel  
changes to the Yellow/white color.  
Note  
Audio On/Off of 4 split mode cannot be set in the playback screen.  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-6  
Fre e ze a n d Zo o m  
4
Freeze Function  
Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode.  
You can set Freeze On/Off with [FREEZE] Button and [FREEZE LED] is turned on or off  
depending on the Freeze On/Off setup condition.  
Zoom Function  
Zoom function enlarges the selected area to double size, and it is only available in the  
single mode.  
If the [ZOOM] button is pressed in the single mode, the Zoom area appears. Use the  
UP/DOWN/LEFT/RIGHT key to adjust the position of Zoom area. After selecting the Zoom area,  
press the [Enter] button to display the selection area in double size. You can adjust the video  
image position with the UP/DOWN/LEFT/RIGHT key at the Zoom in state. For Zoom off at the  
Zoom in state, use the [ZOOM] button.  
[ZOOM LED] is turned on or off depending on the Zoom On/Off setup condition.  
4-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-7  
SHR-2040/2041/2042 USER’S MANUAL  
Eve n t Mo n ito rin g  
5
Event monitoring displays the channel synchronized with a event on the screen when a special  
event (Sensor/Motion/Video Loss) occurs. Event monitoring On/Off and event duration setup is  
available in [Menu]■[Monitoring] mode.  
If you set the event monitoring interval to 5 seconds and an event occurs at CH2 in  
the beginning as following figure, the system will display CH2 in the full screen for 5 second.  
If another event occurs within 5 seconds, it is displayed together with the existing event. As the  
following figure, both CH1 and CH3 events occur within 5 seconds (for example, after 4  
seconds) after occurring CH2 event, these three events are split into 4 screens.  
If the new event does not occurs during the event duration, the system will return to the  
previous Live mode. Pressing the [ALARM] button during the event duration makes the event  
monitoring stop. On occurring an event, [ALARM LED] is turned on. Press the [ALARM] button  
to turn [ALARM LED] off.  
The alarm setup is initialized and the event icon disappears, and the event monitoring is off if it  
is on when pressing the [ALARM] button. After alarming, the event recording is continued again  
for set time.  
Note  
The Alarm LED does not turn off even though the event recording is finished. To turn the  
Alarm LED off, press the [ALARM] button.  
4-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-8  
Sp o t-o u t m o n ito rin g  
6
Spot-out Monitoring has nothing to do with Live Screen Output, it monitors the full screen of a  
certain channel. If you select the Monitoring in the MENU, the one channel among CH1 ~ CH4  
is output with a Spot-out or channels are output one by one at an interval as Auto Sequence  
Mode in the Live Mode. Live screen icon does not appear in the spot-out monitoring.  
The interval is as same as the Auto Sequence time in the Live Mode. If the Spot-out Event  
Monitoring is On, it is possible to see the event channel with Spot-out. In case of simultaneous  
event occurrence at more than one channel, the lowest numbered event channel has the first  
priority to be spotted out.  
Caution  
If the built-in HDD is not connected, or it operates with power applying in error,(  
indicating "built-in HDD error" is displayed at the top of left.  
At this time,  
)
(1) Live screen mode  
(2) Monitoring mode by Smart Viewer  
operate only and the other functions including recording, search, playback, menu  
setup, and PTZ do not operate.  
If the above problem is occurred, be sure to contact a service center to settle the problem.  
Caution  
If the fan in a set does not operate or has a problem, a fan error message pops up in the live  
screen as below picture. And the fan error icon  
appears at the top of left . If it is, check  
the fan in the set. The icon at the top of left disappears automatically if the fan recovers its  
operation.  
Fan Information  
A error occurs in the fan.  
Refer to the manual.  
4-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5  
Ch a p te r 5  
Me n u Se tu p  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-1  
SHR-2040/2041/2042 USER’S MANUAL  
Be fo re Use  
■
Selection  
The yellow cursor shows the current window. Use the œ,ƒ,¦, ‹ key in the front to move  
the cursor on your desirous menu. If you press the “Enter” key with the cursor clicking on  
your desirable menu, the system will enter the new mode.  
Press the “Enter” key to finish the selection. On seeing Drop Down Menu, use the œ or ƒ  
key to move the cursor on your desirable menu.  
■
■
“OK” or “Cancel” in Menu Setup Window  
Once changed, the new menu setup procedure will be finalized by pressing “OK”.  
Pressing “Cancel” will cancel the new setup and return to the upper menu.  
Front “MENU” and “SEARCH” Button  
The MENU button or SEARCH button, if pressed first, acts as an entrance button.  
Once entering, it reverses the page to the previous one.  
■
■
The “>” or “V” mark beside the title copies the line in the arrow direction to the value of the  
first line.  
The first page of the menu is structured as follows.  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-2  
Sy ste m  
1
■
System Menu has the following items in detail.  
Date/Time/Language Setup  
■
■
Press the “Enter” key and the ¦, ‹ key to move to Y/M/D.  
Use the œ, ƒkey to change the date.  
Press the “Enter” key to come out of the mode.  
Time  
Press the “Enter” key and the ¦, ‹ key to move to H/M/S.  
Use the ¦, ‹ key to change the time.  
Press the “Enter” key to come out of the mode.  
■
Once changed, the date and time will remain unchanged until you press “OK” or  
“Cancel”.  
5-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-3  
SHR-2040/2041/2042 USER’S MANUAL  
Note  
[Date/Time Change]  
Pressing “OK” after you change date and time, you will be asked by a pop-up window  
if you really confirm the change. Here, press ”Yes” to change the time. Since Date/Time does  
not change in backup process, be sure to stop the backup process before you change  
Date/Time. If the date or time is changed, the system reboots.  
Caution  
[Date/Time Change]  
If the Date/Time changes to the original value, the data recorded before the change may be  
deleted. For example, if the time is changed from 8 am to 7 am, all the data recorded between  
7 am and 8 am will be deleted.  
■
■
■
Date Format  
The system supports 3 formats, YYYY-MM-DD / DD-MM-YYYY / MM-DD-YYYY.  
Time Format  
The system supports 2 formats, 24 Hour / 12 Hour(AM/PM).  
Language  
After selecting a language, OSD is expressed in the selected language.  
The available language is added in the list.  
■
DST(Daylight Saving Time)  
DST sets the watch one hour faster than the local standard time. This menu  
makes the system count for DST in DST regions. The system goes one hour faster  
and reboots at the setup date.  
If the DST is Off, it does not operate. And it is impossible to enter the right date  
menu. To setting the DST, enter the start time on the left and the end time on the  
right of ‘~’. DST is allowed to set Month/Date/Time only.  
Year/Minute/Second remains inactivated.  
Note  
[On DST Setup]  
Backup in progress will be cancelled. Recording in progress will be suspended for a moment  
until rebooting.  
Caution  
[On DST Operation]  
As the system goes one hour earlier, the data recorded since an hour ago will be deleted.  
As DST activates at the preset time, you are recommended to take the utmost care of  
preventing any trouble incurred by data deletion or rebooting.  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-4  
Password  
■
■
The Default Password is 4321.  
New Password  
This is used to change the system password inside SHR-2040/2041/2042. You are  
allowed to create a password up to 4 digits. Press the “Enter” key and a channel  
button from 1 ~ 4 at the left. Press the “Enter” key after change to move to “New  
Password Confirm”.  
■
■
New Password Confirm  
This confirms a new password. You shall be obliged to input New Password in  
the above row first. Without New Password input, New Password Confirm input  
has no effect.  
Password Setup  
If it is set to On, a window for asking the password pops up when pressing the  
menu button.  
If it is set to Off, you are allowed to enter the menu mode without being asking the  
password when you press the menu button.  
■
All Key Lock On  
If you select this, the system will enter the Live Mode immediately. If you press any  
button in the front, the Password window will pop up. If the correct password is  
input, the lock function is cancelled after popping up a message for the  
cancellation of Key Lock.  
Note  
[All Key Lock On]  
If you select this, the system will change to the Live Mode immediately and keys will be  
locked.  
5-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-5  
SHR-2040/2041/2042 USER’S MANUAL  
Load Factory Default  
■
It used to initialize all the menu setup values. The recorded data will not be deleted.  
Press “OK” in the confirmation window to start initializing.  
System Log  
■
■
System Log is used to check the important record by an administrator.  
It displays such contents of a system related log and its execution date/time as System  
Start, System Termination, and Menu Setup Change.  
■
■
■
■
First : Moves to the first Log page.  
Prev : Moves to the previous Log page.  
Next : Moves to the next Log page.  
Last : Moves to the recent Log page.  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-6  
■
System Log List  
System Start  
Starts the system.  
Time Change  
Changes the Date/Time.  
Initializes the system.  
Changes the system S/W.  
No Space in the HDD  
Starts the backup.  
Login(Admin)  
Viewer Login (Admin)  
Viewer Logout (Admin)  
Viewer Login (User)  
Viewer Logout (User)  
Enters into the menu.  
Comes out of menu.  
Load Factory Default  
System Upgrade  
Disk Full  
Logout(Admin)  
Login(User)  
Logout(User)  
Backup Start  
Setup Start (Local) Set  
Setup End (Local) Set  
Backup End  
Ends the backup.  
Backup Stop  
Stops the backup.  
Setup (Remote): Viewer Sets the menu.  
Backup Fail  
Backup Failure  
Play Back Start  
Starts the playback.  
ATA HDD Erase  
USB HDD Erase  
USB MEMORY Erase  
Erases the ATA Data.  
Erases the USB HDD data.  
Erases the USB MEMORY data.  
Play Back End  
Ends the playback.  
Record Start CH[N]  
Record End CH[N]  
Power Failure Recovery  
Starts the Channel [n] recording  
.
Overwrite Playback Stop Stops the playback by overwrite.  
Backup Stop(Overwrite) Stops the backup by overwrite.  
Ends the channel [n] recording.  
Returns the system after power interruption.  
Event Log  
■
■
■
■
■
■
It used to check the record regarding Event like Alarm / Motion / Video Loss.  
It displays the contents of a log regarding event and its execution date / time.  
First : Returns to the first Log page.  
Prev : Back to the previous Log page.  
Next : Forwards to the next Log page.  
Last : Moves to the recent Log.  
■
Event Log List  
Video Loss CH[N]  
Means the occurrence of Channel [N] Video Loss.  
Means the occurrence of Channel [N] alarm.  
Means the occurrence of Channel [N] Motion.  
Alarm Detection CH[N]  
Motion Detection CH[N]  
5-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-7  
SHR-2040/2041/2042 USER’S MANUAL  
System Information and Setup  
■
■
Software Version : Displays the current version. Setup is not available.  
Broadcast Format : Displays the current Format(NTSC/PAL) . Setup is not available.  
Mac Address : 6 Byte hardware address. Setup is not available.  
■
■
Device Erase  
This erases the data in ATA / USB HDD / USB memory. Click the checkbox of the device  
that you want to erase and press “OK” You are not allowed to erase the data in Backup  
progress.  
■
USB S/W Upgrade  
You can update the program by use of USB device. If there is no device, "USB S/W  
Upgrade fail" window pops up.  
Note 1  
[Internal HDD]  
This is a physical hard disk connected with the IDE cable inside the SHR2040/2041/2042 main body, and  
stores data.  
[External HDD]  
This is a physical hard disk connected with the port and terminal in the back of the  
SHR2040/2041/2042 main body, and stores data.  
This can be used as Extended HDD or Backup HDD.  
- Extended HDD : Supplements Internal HDD quantity. Connected, it takes the place  
of Internal HDD.  
- Backup HDD : Backs up the data recorded in the set.  
Note 2  
[ATA]  
Usage : Internal HDD  
This is a physical hard disk connected with the IDE cable inside the SHR2040/2041/2042 main body.  
[USB]  
Usage : External HDD(Extended HDD or Backup HDD)  
This is a physical hard disk connected with the USB port in the back of the SHR SHR2040/2041/2042  
main body,  
5-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-8  
Caution  
[Device Erase]  
Data will not be deleted in the backup mode.  
Please be sure to stop the backup before you delete a data. In the recording mode, suspend  
the recording and delete a data.  
Caution  
[USB S/W Upgrade]  
Download the software to upgrade at http://www.sec.co.kr, CCTV Part.  
If the USB memory to upgrade has a format not being supported by DVR set, the upgrade is  
impossible.  
In this case, use the “device erase” of menu 5-7 system information and setup.  
Only one file to upgrade is allowed in the USB Memory.  
HDD Setup  
■
■
HDD Information  
Displays the number, capacity, and status of ATA and USB device. Setup is not available.  
Status : Internal HDD, External HDD, Backup HDD  
External HDD Setup  
1. Backup/External type  
You are able to determine the usage of USB.  
Not Defined ■ Appears when the usage of connected HDD is not defined.  
You can set to External or Backup type.  
No Device ■ Appears when there is no HDD connected. You are able to connect it by  
pressing the right connection TAB after connecting HDD  
External ■ Appears when the connected HDD is set to External type. It may used as a  
backup HDD if you press the “Enter” key and turn to Backup.  
Backup ■ Appears when the connected HDD is set to Backup. If you press the “Enter”  
key and turn to External(Extend), it can be used as an External HDD.  
5-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-9  
SHR-2040/2041/2042 USER’S MANUAL  
HDD Mode Setup  
■
■
HDD End Mode  
Stop : Stops recording when HDD is full during the recording.  
Overwrite : Deletes the original data and save a new data when HDD is full during the  
recording.  
HDD End Beep  
On : Beeps when the HDD is full in the recording mode.  
Off : Although the HDD is full in the recording mode, the beep sound is not heard.  
Note  
If the HDD is full, the Disk Full Icon(  
) is appeared.  
5-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-10  
Caution  
[Disk Overwrite]  
In the overwrite Mode, the previous Event data is deleted and the mode is changed.  
Remote control Device  
■
MENU for the use of Samsung system keyboard  
Remote Control Device  
Device  
Samsung System Keybord  
ID Baudrate Parity Date Stop  
03 4800 None  
Duplex  
8
1
Half Duplex  
■
■
Device  
A Remote Control Device, being connected to the RS485 port.  
ID  
This is a private ID of SHR-2040/2041/2042.  
This private ID is essential for SSC-2000 because SSC-2000 can control many  
SHR-2040/2041/2042 DVRs.  
■
Baudrate  
Baudrate to communicate with SSC-2000  
It should be same to SSC-2000 Baudrate for communication.  
■
■
■
■
Parity  
Sets up one of None / Even / Odd.  
Data  
Sets up either 7 or 8.  
Stop  
Sets up either 1 or 2.  
Duplex  
Sets up either Half Duplex or Full Duplex.  
Note  
If you select Remote Control Device, you cannot control the PTZ device with  
SHR-2040/2041/2042. The PTZ button in the front of SHR-2040/2041/2042 becomes  
inactivated. Press the PTZ button and the PTZ ban icon(  
RS-485 port setup was done for Remote Control Device.  
) will appear. It’s because the  
5-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-11  
SHR-2040/2041/2042 USER’S MANUAL  
System Shutdown  
Remote Control Device  
■
Terminates the work in action safely and turns the power off. Press “OK” in the confirmation  
window and plug out when you see “Safe to Power Off”.  
Caution  
[System Shutdown]  
Power-off without terminating the system in the System Shutdown menu may incur  
improper motion like data loss and disk failure. Power-off shall be done in the System  
Shutdown menu.  
5-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-12  
Ca m e ra  
2
■
The detailed Camera Menu items are as follows.  
Camera Config.  
■
■
Video  
On : Camera images from a selected channel appear.  
Off : Camera images from a selected channel disappear.  
Covert1 : Displays the information except for the Video information of selected channel.  
Covert2 : Does not display the any information.  
Audio/Cam name/Auto sequence setup are impossible in the Off channel.  
Audio  
On : Makes the sound of selected channel on.  
Off : Makes the sound of selected channel off.  
5-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-13  
SHR-2040/2041/2042 USER’S MANUAL  
■
Title  
You can name the camera of selected channel.  
If you press the [Enter] key, the Virtual keyboard will come out.  
‹¤Virtual Keyboard  
If you move the cursor, you can type text by text.  
Up to 15 texts can be typed.  
Keyboard cannot be composed of all spaces.  
Pressing Caps Lock changes the keyboard that can be selected. (2 Modes)  
■
Auto Sequence  
You are allowed to set the duration of each channel at the Auto Sequence channel in the  
Live Mode.  
A channel, set to Off, does not operate in the Auto Sequence Mode.  
5-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-14  
PTZ Device  
■
■
ID  
It is an ID for PTZ Camera and available to set from 0 to 255.  
Protocol  
It is supported by the PTZ device.  
The following protocols are now being supported.  
Samsung/ Vicon/ Panasonic/ AD/ Philips/ Erna/ PelcoD/ PelcoP/Vcltp/ Diamond/ Kalatel  
■
■
■
■
■
Baurate  
Baurate is supported by the PTZ device. 600/ 1200/ 2400/ 4800/ 9600/ 19200/ 38400  
Parity  
It is set to the one of None, Even, and Odd.  
Data  
It is set to either 7 or 8.  
Stop  
It is set to either 1 or 2.  
Duplex  
It is set to either Half Duplex or Full Duplex.  
Caution  
The above items shall be same to the PTZ device setup.  
For the details, please refer to User Manual of the PTZ device manufacturer.  
5-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-15  
SHR-2040/2041/2042 USER’S MANUAL  
Screen Setup  
■
It is a window to set Brightness/Contrast/Color for the camera image of each channel.  
Put the cursor on the channel that you want to adjust and set Brightness/Contrast/Color.  
Once selected, the channel appears in the right PIP area. Use the œ or ƒ button to adjust  
the value from 0 to 100.  
■
■
If you mark ■ in the select CH, all the channel values will become the same as the finally  
selected channel value.  
“Default value” resets the current channel to the basic value of 50.  
5-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-16  
Mo n ito rin g  
3
■
Event Monitoring  
It is possible to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous.  
■ Off : Event Monitoring does not operate to turn to the screen where an event occurs.  
■ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : Sets the duration time of screen in the Auto Sequence  
mode.  
■ Continuous : The Event Monitoring screen remains alive until you press the “Alarm”  
button in the front to cancel the screen manually.  
■
OSG Display  
■ Date : The date is displayed on the screen when it is On, and not displayed when it is Off.  
■ Time : The time is displayed on the screen when it is On, and not displayed when it is Off  
.
■ Cam name : The Cam name is displayed on the screen when it is on, and not displayed  
when it is off.  
■ Status : Audio/Ptz is displayed on the screen when it is on, and not displayed when it is off.  
■
Spot Out Channel  
Spot Out channel is used to let one of two monitors monitor a channel, focusing on it.  
Spot Out channel supplies two functions, continuous monitoring of only one channel and  
Auto Sequence to display all the channels one by one.  
■ Auto Sequence setup ranges from Ch1 to Ch 4.  
■ In the Auto Sequence mode, Spot Out channels are displayed in turn.  
■ Duration time for Auto Sequence is as same as set for Camera setup.  
■
Spot Out Event Monitor  
Sets if event monitoring will be executed for Spot Out channels.  
■ Off : The event monitoring dose not operate in the Spot Out channel.  
■ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : Sets the duration time of screen in the Auto Sequence  
mode.  
■ Continuous : Once scrolled down, the screen remains displayed until you delete “Alarm”  
LED in the front manually.  
5-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-17  
SHR-2040/2041/2042 USER’S MANUAL  
■
Monitor  
You are not allowed to connect VGA OUT and Composite/S-Video OUT simultaneous-  
ly. Consequently, the user is obliged to choose either Composite Output or S-Video  
Output.  
■
■
Composite : Makes the output come out through the “Composite / S-Video OUT” port.  
VGA : Makes the output come out through the “VGA Out” port.  
When changing the output from Composite to VGA or from VGA to Composite, the  
system reboots automatically.  
■
1 CH Support  
1 CH DVR is supported. If 1 CH Support is On, 1 CH is supported. If 1 CH Support is Off,  
4 CH is supported.  
If 1 CH Support is On, a set reboots and support 1 CH.  
Caution  
[Video Out]  
When setting the Composite Output, VGA output does not come out.  
When setting the VGA Output, Composite Output does not come out.  
If you press the No. 1 button for 5 seconds in the Live Mode with keeping the MODE button  
pressed, the system will change from VGA to COMPOSITE or from COMPOSITE to VGA and  
reboot.  
[1 CH support]  
In the case of 1 CH support, the event monitoring, Spot out channel, Spot out event  
monitoring cannot be set.  
Full D1/Half D1/ CIF is supported for the video size in the 1 CH.  
If the Full D1 is set and 1 CH support Off is selected, the video size in the 4 CH set to CIF.  
In the 1 CH setup, the system value is initialized.  
5-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-18  
Re co rd in g Mo d e  
4
Record Mode  
■
Details for Record Mode Menu are as follows.  
NTSC  
PAL  
If you press the front “REC” button, the mode value to be recorded will be set.  
■
For the setup of Event Recording Mode value, refer to 5-20. Event Recording  
Mode Setup Menu.  
■
Mode  
On : The current channel is recorded if the REC button is pressed.  
Off : The current channel is not recorded even thought the REC button is pressed. The  
default value is set to “On”.  
■
■
Quality  
It sets the Quality.  
Set to the one among Very high/High/Normal/Low.  
Rate  
It sets the Rate means the number of screen recorded every second.  
If it is set to 15 ips(NTSC)/12.5 ips(PAL), the system records too many screens per second  
and the playback continues intermittently since recording is more detailed.  
This is appropriate for concentrated monitoring zone setup.  
IIn case of NTSC, select one out of 30 ips / 15 ips / 10 ips / 7.5 ips / 5 ips / 3 ips / 1 ips. In  
case of PAL, select one out of 25 ips / 12.5 ips / 8.33 ips / 6.25 ips / 5 ips / 2.5 ips / 1 ips.  
The Recording Menu will be activated depending on Video On/Off in the Camera Setup  
(Menu5-12). When less than 2 cameras are activated at HALF D1, the frame rate of  
recording may start from 30IPS and when more than 3 cameras are activated at Half D1,  
the frame rate of recording may start from 15ips(NTSC) / 12.5ips(PAL). CIF supports from  
30ips(NTSC) / 25ips(PAL) regardless of the number of activated camera.  
■
Video size  
The Video size is displayed at the bottom of left.  
5-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-19  
SHR-2040/2041/2042 USER’S MANUAL  
Record Video size Mode  
■
Video size  
It sets the video to be recorded.  
Half D1 : (NTSC) 720x240(N) . Normal  
(PAL) 720x288(N) . Normal  
CIF  
: (NTSC) 352x240(C) . CIF  
(PAL) 352x288(C) . CIF  
■
Auto Deletion  
Press the [Off] button at the bottom of left to select either OFF or On.  
Select “On” to move to the Date selection button and to limit the search date.  
If you select “Off”, you cannot move to the Date selection button and to limit the search  
date.  
The date is limited from 1 to 99 days.  
Note  
To select Full D1, set 1 CH Support to On in the monitoring mode.  
5-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-20  
Eve n t Re co rd Mo d e  
5
■
The detailed items of Event Record Menu are as follows.  
Event Record Mode setup  
NTSC  
PAL  
■
■
Event Record Mode setup  
Sets a mode to be recorded when an event occurs.  
V. Size (Video Size )  
Sets the size of a screen to be recorded.  
Half D1 : (NTSC) 720x240(N) ■ Normal  
(PAL) 720x288(N) ■ Normal  
CIF  
: (NTSC) 352x240(C) ■ CIF  
(PAL) 352x288(C) ■ CIF  
5-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-21  
SHR-2040/2041/2042 USER’S MANUAL  
■
■
Quality  
Quality will be determined.  
Select the one among Very High/High/Normal/Low.  
Rate  
Sets the Rate the number of screen recorded every second.  
It you set to 15ips, the system records too many screens per second and play continues  
intermittently since recording is more detailed. This is appropriate for concentrated  
monitoring zone setup.  
In case of NTSC, select the one of 30 ips/ 15 ips/ 10 ips/ 7.5 ips/ 5 ips/ 3 ips/ 1 ips.  
In case of PAL, select the one of 25 ips/ 12.5 ips/ 8.33 ips/ 6.25 ips/ 5 ips/ 2.5 ips/ 1 ips.  
■
■
The Event Recording setup menu will be activated depending on Video On/Off in  
Camera Setup (Menu5-12).  
When the video size in the Camera Setup Menu is set to Half D1 and less than 2  
cameras are activated, the frame rate of recording may start from  
30ips(NTSC)/25ips(PAL) and when the video size in the recording mode is set to  
Half D1 and more than 3 cameras are activated, the frame rate of recording may  
start from 15ips(NTSC) / 12.5ips(PAL). CIF supports from 30ips(NTSC) /  
25ips(PAL) regardless of the number of activated camera.  
■
Pre-Event  
Pre-Event Section  
Event time  
Records the situation until Alarm is issued.  
Off : No recording  
5sec/ 10sec/ 20sec/ 30sec : The recording time options before Alarm issue  
■
Post-Event  
Post-Event Section  
Event time  
Records the situation since Alarm is issued.  
Off : No recording  
5sec/ 10sec/ 20sec/ 30sec/1min/3min/5min/10min/20min: Sets the recording time after an event occurs.  
■
Video size  
The Video size is displayed at the bottom of left 5-19.  
5-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-22  
Alarm Detection Setup  
■
Off : Sensor does not operate.  
■
N.O(Normal Open) Sensor : Sensor remains open all the time and if closed,  
an alarm will be issued. (A Contact)  
■
N.C(Normal Close) Sensor : Sensor remains closed all the time and if open,  
an alarm will be issued. ( B Contact)  
■
Cam  
Sets a camera that will synchronize with the current sensor. The default value is currently  
set to the sensor number. A sensor shall be synchronized with at least a camera.  
Multi-selection is possible.  
■
Alarm-out  
Sets the Alarm-Out when Alarm Sensor sounds.  
5 Alarm Outs are supported un the present.  
Choose an alarm-out that you want to synchronize with the current sensor.  
Multi-selection is possible.  
■
Beep-Out  
Sets the Alarm-Out Duration. Alarm-Out continues for the set value.  
Off / 3sec / 5sec / 10sec / 20sec / 30sec  
5-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-23  
SHR-2040/2041/2042 USER’S MANUAL  
Motion Detection Setup  
■
■
Motion Detection Mode  
Off : Motion Detection does not operate  
On : Motion Detection operates.  
Area  
Selects the Motion Detection area. It is composed of 45x40(NTSC)/45x48(PAL) sized Block.  
It is impossible to set 4 block rows(Up/Down/Left/Right) to allow them to be displayed in all  
monitors.  
‹ Select All :  
Selects the whole area.  
‹ Select Block :  
Selects a block every time. Selection is done by a toggle system.  
‹ Select Quarter : Splits the whole area into 4 pieces, which enables selecting a fourth of  
the whole area.  
‹ Clear All :  
‹ Save & Exit :  
‹ Exit :  
Cancels the whole area.  
Saves and exits.  
Exits without saving.  
5-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-24  
■
■
Sensitivity  
Sets the sensitivity of motion detection. Sensitivity grade consists of Low ■ Medium ■ Very  
High in the ascending order.  
Alarm-Out  
Sets the Alarm-Out when Motion occurs.  
5 Alarm Outs are supported.  
Select an alarm-out that you want to synchronize with the current motion channel.  
Multi-selection is possible.  
■
Beep-Out  
Sets the Alarm-Out Duration. Alarm-Out continues for the determined duration.  
Off/ 3sec/ 5sec/ 10sec/ 20sec/ 30sec  
Video Loss Detection Setup  
■
■
Video Loss State  
Off : Video Loss does not operate.  
On : Video Loss operates.  
Alarm-Out  
Selects the Alarm-Out when the current Video Loss occurs.  
3 Alarm Outs are supported in the present. Select an alarm-out that you want to  
synchronize with the current motion channel. Multi-selection is possible.  
■
Beep-Out  
Sets Alarm-Out Duration. Alarm-Out continues for the determined duration.  
Off/ 3sec/ 5sec/ 10sec/ 20sec/ 30sec  
5-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-25  
SHR-2040/2041/2042 USER’S MANUAL  
Re co rd Sch e d u le  
6
This setup selects a time to record automatically.  
Selection by the day or by the time is available.  
The default value is set to “Event Record”.  
■
■
Press “CH >” copies the value of Channel 1 to all the channels.  
The horizontal axis numbered from 0 to 23 represents the time value.  
The vertical axis numbered from S to H represents the day value. (H : Holiday)  
Selection by the day or by the time is available.  
■
■
Pressing “ALL” converts the overall setting of the selection window into  
Continuous ■ Event Record ■ Schedule/Event Record.  
Record Schedule  
Recording starts automatically on the preset time.  
Recording follows the condition that set in 5-18.Record Mode.  
■ Refer to 7-2 Record Schedule.  
■
Event Recording  
Recording starts automatically when an event (Alarm/Motion Detection/Video Loss)  
occurs within a setup time.  
Recording follows the condition that set in 5-20.Event Record Mode setup.  
■ Refer to 7-3 Event Recording.  
■
Schedule Record is yellow, Event Record is Blue, and Schedule/Event  
Record is red.  
5-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-26  
■
■
Schedule / Event Record  
On occurrence of Event, Continuous Recording is replaced with Event Recording Mode.  
Holiday  
If you press “Holiday”, a calendar pops up and you are able to designate holidays.  
Move to a date and press “Enter” to complete designation.  
Press “Enter” once more to cancel designation.  
“H” at the bottom of the table means a holiday.  
5-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-27  
SHR-2040/2041/2042 USER’S MANUAL  
Ba ck u p  
7
Backup  
■
■
■
If there is a device, the free space and the backup device is displayed.  
Select a date, time, and camera No. to backup, and press “Start”.  
When you change Start Date/Time or End Date/Time, free space keeps updated in  
the Free Space zone.  
■
A file name is composed of Folder/File Name. A folder is composed of the backup  
date(YYYYMMDD) while a file name is composed of the time(HHMM).  
A file may be renamed by the virtual keyboard. A file name can composed of the  
maximum 5 letters.  
■
■
In case that more than one backup device is connected, click the box in the  
bottom of left corner to select a backup device.  
If there is no backup device, Warning sign pops up. Select and connect Backup  
Device in 5-8.HDD Setup and proceed the backup.  
■
■
Press the “Stop” to stop the backup.  
Pressing Cancel during the Backup returns to the upper menu but this does not  
affect the backup process.  
■
In case of USB HDD, the AVI check is impossible.  
Caution  
[In Backup Process]  
Pressing THE “Cancel” returns to the upper menu but this does not affect Backup process.  
Press “Stop” to stop the backup.  
The speed of the set may down during the backup.  
Note  
SHR-2040 supports the internal CD-R/ W.  
Note  
In case of AVI backup, the backup playback is available in the PC, but it is not available in the set.  
5-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-28  
N e tw o rk  
8
IP Setup  
■
■
Connection Mode  
Designates the kind of the network connected to the main body of SHR-2040/2041/2042.  
Static IP  
Dynamic IP  
: When the main body is connected to the network with Static IP.  
: When the main body is connected to the network with Dynamic IP supplied  
by DHCP.  
ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE.  
Bandwidth  
Designates the network speed to which the main body of SHR-2040/2041/2042 is  
connected.  
Unlimited / 2 Mbps / 1 Mbps / 600 Kbps / 300 Kbps  
In case of ADSL, the bandwidth should be selected 600 Kbps or 300 Kbps.  
Caution  
When the main body is connected to the network using high speed LAN, set to 1 Mbps or 2  
Mbps. When the main body is connected to the network supporting low bandwidth such as  
ADSL, set below 600 Kbps. If you set Bandwidth high though the main body is connected to a  
slow network, the network load will get heavy therefore the connection with Smart Viewer or  
video monitoring may be instable.  
Note  
In case of ADSL, the Protocol type is fixed to TCP.  
■
■
Admin Password  
Used for the connection between Smart Viewer and the set with the authority of Admin.  
The password can be input 8 digits in maximum.  
Press "Enter" and the left numeric keys from 1 to 4 for setup.  
The default password for ADMIN is 4321.  
User Password  
Used for the connection between Smart Viewer and the set with the authority of user.  
The password can be input 8 digits in maximum.  
Press "Enter" and the left numeric keys from 1 to 4 for setup.  
The default password for USER is 4321.  
5-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-29  
SHR-2040/2041/2042 USER’S MANUAL  
■
IP  
Sets the IP address for the main body of SHR-2040/2041/2042 to connect with the network.  
If the Connection Mode is set to Static IP, you shall type in IP yourself.  
If the connection mode is Dynamic IP or ADSL(PPPoE), the IP allocated by the DHCP server or  
ADSL company will be automatically displayed. In case of failure of DHCP or ADSL connection,  
000.000.000.000 will be displayed. Then, press OK to retry connection to get IP. If you continue to  
fail in DHCP or ADSL connection, keep the main body of SHR-2040/2041/2042 off for a while and  
turn it on for retry.  
■
■
■
Gateway  
Sets the Gateway Address in the SHR-2040/2041/2042 main body.  
Subnet Mask  
Sets the Subnet Mask Address in the SHR-2040/2041/2042 main body.  
DNS  
Sets the DNS Address in the main body of SHR-2040/2041/2042. The default value of DNS is  
168.126.63.1. Generally, you don°Øt have to alter the DNS default but you may be hard to  
connect to the network sometimes if you use DHCP or ADSL.  
In this case, call the network manager or ADSL company to set up a new DNS address.  
■
■
ADSL User ID  
If the main body of SHR-2040/2041/2042 is connected with the ADSL(PPPoE) network, input  
User ID subscribed to the ADSL company. You may input User ID with a Virtual keyboard as long  
as 40 digits irrespective of alphabets, numbers, or symbols.  
Password  
If the main body of SHR-2040/2041/2042 is connected to the ADSL(PPPoE) network, input the  
user password subscribed to the ADSL company. You may input the password with a Virtual  
keyboard as long as 40 digits irrespective of alphabets, numbers, or symbols.  
Caution  
Be sure to set IP/Port/SubnetMask/Gateway/DNS to let Smart Viewer connect with the main  
body of SHR-2040/2041/2042.  
Wrong IP/Port/Gateway/SubnetMask/DNS may prevent Smart Viewer from being connected  
to the main body of SHR-2040/2041/2042.  
Please call the network manager or ADSL company to get each setting value.  
Caution  
In case of ADSL, the audio is not played in the SmartViewer.  
5-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-30  
Transfer Protocol Settings  
■
You may select either TCP or UDP for the protocol type.  
If you select ADSL from the IP setup page, only TCP is available.  
While TCP is selected, Audio transmission is not available.  
■
■
The available Port(TCP) ranges from 554 to 998 and the port number will be changed by 4.  
Once the first digit is determined, the following 3 digits will change accordingly.  
The available Port(TCP) ranges from 8000 to 9760 and the port number will be changed by 160.  
Once the first digit is determined, the remaining digits will change accordingly.  
■
■
Unicast is set to the default value and Multicast can be selected in Unicast / Multicast.  
Multicast IP will be activated and its setup is available only when Multicast is selected from  
Multicast/Unicast.. Select a number from 224.0.0.0 to 239.255.255.255 for the D-Class IP  
address.  
■
TTL will be also activated and the value from 0 to 255 can be set only when Multicast is selected  
from Multicast / Unicast. The default value is 5.  
Note  
If you want to connect IP Router with the main body of SHR-2040/2041/2042, you shall  
designate a port for SHR-2040/2041/2042 in the IP Router setup menu.  
The main body of SHR-2040/2041/2042 uses 4 ports for TCP communication.  
In addition, if you want to use the DHCP function backed by IP Router to allocate Dynamic IP to  
the main body of SHR-2040/2041/2042, you shall designate a port for the IP which  
SHR-2040/2041/2042 has been allocated by the IP Router setup menu.  
If you use IP Router, you are recommended to rather determine IP and Port numbers to be  
allocated to the main body of SHR-2040/2041/2042 from the IP Router setup menu, set the  
connection mode to Static IP for the main body of SHR-2040/2041/2042, and input the  
determined IP and Port number in IP Router than use the DHCP function.  
Please refer to the IP Router User’s Manual or call the manufacturer to set up IP Router.  
5-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-31  
SHR-2040/2041/2042 USER’S MANUAL  
Callback Settings  
■
The Callback function is used to forward a callback message to the IP where SmartViewer  
is in action in case Alarm, Motion Detection, or Video Loss event occurs.  
■
■
On/Off : Off is default but you may choose On.  
IP Address : IP setting is available only when On is selected from On/off Setting.  
Select the IP address of PC where SmartViewer is in action.  
■
■
Port(UDP) : You may choose one from 7900 to 7999 and the number changes by 1.  
Selects the Port value for the Callback Connection menu from SmartViewer Setup.  
Retrial : You may choose one from 1 to 20 and the number changes by 1.  
Caution  
- Though Callback is set to ON, any Callback message will be created unless Alarm, Motion  
Detection, and Video Loss are set by EventRecord.  
- Unless the Callback button is clicked, SmartViewer does not receive any Callback message.  
5-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-32  
N e tw o rk Se tu p  
9
Port Setup for SmartViewer Connection  
■
The Port value for DVR registration of SmartViewer (Setup ■ Site Setup) shall be as  
same as that of the set (TCP).  
■
If you want to use the IP Router, you shall forward the activated Port depending on the  
current setting value.  
- If set to TCP, allocate 4 ports to the IP Router whose Port(TCP) was set.  
- If set to UDP, allocate 4 ports whose Port(TCP) was set and 160 ports whose Port(UDP) was  
set to the IP Router.  
In the event of TCP Setup from Transfer Protocol Setup Page  
■
The ports allocated to Port(TCP) will be used for SmartViewer connection control and  
stream forwarding.  
In the event of UDP Setup from Transfer Protocol Setup Page  
■
The ports allocated to Port(TCP) will be used for SmartViewer connection control and  
the ports allocated to Port(UDP) will be used for stream transfer.  
■
If you set to Multicast  
- Both MultiCast IP and TTL Setup will be activated.  
- MultiCast IP means the group address(D-Class IP Address : 224.0.0.0 ~ 239.255.255.255) for  
MultiCast Forwarding.  
- TTL(Time To Live) indicates how many Routers will be passed for MultiCast Forwarding.  
- When you are unable to use Multicast by the Network(LAN or ADSL) characteristic as both Set  
and SmartViewer are installed, the message, “Not Connected” will be displayed in the  
SmartViewer screen. Please alter the TCP or UDP(Unicast) setting value.  
■
In the event of poor image from SmartViewer  
- When the bandwidth of the network where Set is installed is smaller than the quantity of transfer  
stream packet, the image is sometimes poor. Set the IP setup bandwidth lower than the current  
setting value. (In case of ADSL, it is recommended 300Kbps or 600Kbps for the bandwidth.)  
- If this effort is no use, alter the protocol type to TCP.  
5-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7  
Ch a p te r 6  
PTZ Ca m e ra Co n tro l  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-1  
SHR-2040/2041/2042 USER’S MANUAL  
PTZ Ca m e ra Co n tro l Mo d e  
1
■
Select a proper PTZ camera Configuration value in MENU to enter PTZ Control Mode.  
PTZ  
) is displayed on the channel in the screen.  
■
■
Selected in MENU, the PTZ symbol(  
If you press the Enter( ) button among direction keys in front of Split Screen, a blue  
¦
bar will appear in the monitor screen. Use direction keys to move this bar until you reach  
the channel with the PTZ symbol and press the PTZ button in front of SHR-2040/2041/2042  
to enter PTZ Camera Control Mode.  
If you succeed in entering PTZ Camera Control Mode, the PTZ symbol on the monitor  
screen will turn yellow from white while the PTZ button in front of SHR-2040/2041/2042 will  
turn blue. PTZ Camera Control Mode supports Pan, Tilt, and Zoom operation.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-2  
■
Other PTZ Camera Control Modes perform its control in a single screen. Press the channel  
selection button in the left front to select the PTZ setting channel and press the PTZ button.  
If you succeed in entering Single Screen PTZ Camera Control Mode, the PTZ symbol on  
the screen will turn yellow from white while the PTZ button will turn blue. Single Screen PTZ  
Camera Control Mode supports Pan, Tilt, and Zoom operation basically and Preset, Camera  
Menu, and other functions additionally.  
[SHR-2040]  
[SHR-2041]  
[SHR-2042]  
■
Press the PTZ button in Live Mode to cancel PTZ Camera Control Mode. After cancellation,  
the PTZ symbol on the screen will turn white from yellow while the PTZ button will lose its  
blue light.  
Note  
If you select Remote Control Device, you may not control PTZ Camera with  
SHR-2040/2041/2042. It’s because the PTZ button in front of SHR-2040/2041/2042  
remains inactivated.  
Press the PTZ button and the PTZ ban icon(  
setup was done for Remote Control Device.  
) will appear. It’s because the RS-485 port  
The some functions of PTZ camera are used under restriction.  
6-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-3  
SHR-2040/2041/2042 USER’S MANUAL  
Ba sic Opera tion of PAN, TILT, & ZOOM  
2
■
PAN  
Press the LEFT or RIGHT button in front SHR-2040/2041/2042 in PTZ Camera Control  
Mode to control PTZ Camera horizontally.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
■
TILT  
Press the UP or DOWN button in front SHR-2040/2041/2042 in PTZ Camera Control Mode  
to control PTZ Camera vertically.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
■
ZOOM  
Press the TELE/WIDE button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to  
zoom in or out PTZ Camera.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
6-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-4  
Pre se t Se tu p  
3
■
Records a certain position of PTZ Camera.  
■
Memorizes up to 20 PTZ Camera positions at the moment.  
Note  
For AD Protocol PTZ Camera, this memorizes only 7 Presets.  
■
Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera  
Control Mode to set up Preset.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
■
After Preset setup, press ENTER.  
6-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-5  
SHR-2040/2041/2042 USER’S MANUAL  
■
■
Move the cursor to right and press ENTER in PTZ Control Mode first. Then, press the  
“Enter” to run P/T/Z/ operation mode in the PIP screen and press the “Enter” again to  
cancel P/T/Z/ Motion Mode.  
Press Enter at the Position Name position to see Virtual Keyboard. Enter the type position  
name and press the “OK” to save the position and position name.  
■
■
Press the “Del” to delete both Position and Position Name with the number.  
Click the Press Del ■ on the top to delete all positions and position names in memory.  
6-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-6  
Ca m e ra Me n u Se tu p  
4
■
Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several  
conditions of PTZ Camera.  
Note  
Panasonic or Samsung Protocol Camera only is authorized for Camera Menu setup.  
■
Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera  
Control Mode to select Camera Menu.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
■
Press the “Preset” button in front of SHR-2040/2041/2042 to return to the upper menu from  
camera menu.  
6-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-7  
SHR-2040/2041/2042 USER’S MANUAL  
Pre se t Vie w  
5
■
Preset setup allows your movement to a certain saved position of PTZ Camera.  
■
Press the VIEW button in front of SHR-2040/2041/2042 in Single Screen  
PTZ Camera Control Mode to select Preset.(For example, Samsung Protocol)  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
(For example, Samsung Protocol)  
■
Control the cursor until it reaches a preset position number that you want to move and you  
can check it in the right PIP Screen.  
6-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-8  
O th e r Vie w  
6
■
Press the “VIEW” button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera  
Control Mode to supply PTZ Camera. This is a very special function.  
Note  
Samsung, Panasonic, PelcoP, or PelcoD Protocol PTZ Camera supports this function.  
Samsung : Auto Pan / Scan / Pattern  
Panasonic : Auto Pan / Sequence / Sort  
Pelco(P,D) : Auto Scan / Frame Scan / Pattern  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
Preset  
Auto Pan  
Scan  
Pattern  
EXIT  
Preset Auto Pan  
Sequence  
Sort  
EXIT  
Preset Auto Scan  
Frame Scan  
Pattern  
EXIT  
Samsung  
Panasonic  
Pelco  
■
■
After you select a function, press Enter. Then the function will be checked and start running.  
If you select other function during the operation, the previous function will  
be unchecked and the current function will be checked.  
(For example, Samsung Protocol)  
■
■
If you put P/T/Z/ during the operation or enter the Preset Setup or Camera Menu Setup  
during the operation, the function in action will be suspended and unchecked.  
Restarting SHR-2040/2041/2042 system during the operation has no effect.  
The function continues its duty and remains checked.  
6-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7  
Ch a p te r 7  
Re co rd in g  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-1  
SHR-2040/2041/2042 USER’S MANUAL  
REC (N o rm a l Re co rd in g )  
1
■
Pressing REC the button starts recording as set in the record mode. Then, REC LED  
lights on and a recording icon appears on the screen. During the recording in HDD,  
the front HDD LED blinks.  
■
During the normal recording, you can stop it by pressing the REC button.  
If the recording stops, REC LED lights out.  
Warning  
If the work that has to stop the recording(Time change, File delete, HDD connect/disconnect  
etc.) is performed during the recording, the current recording stops.  
7-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-2  
Sch e d u le Re co rd in g  
2
■
While “Record Schedule” or “Schedule/Event recording” is selected in the Record Schedule  
menu, Schedule Recording automatically starts. Otherwise, Schedule Recording remains  
inactivated. During the Schedule Recording, Recording Icon appears on the screen.  
During the recording in HDD, the front HDD LED blinks.  
■
If the Event Recording is selected, the recording starts at the every event.  
In this case, the recording is saved according to the Event Record setup of the channel  
(Video size, Recording quality, Frame rate, Pre-Alarm, Post-Alarm).  
Note  
Even in case of an event, Event Recording will not start unless Event Recording or  
Schedule/Event recording is selected in the Schedule Recording.  
Warning  
If the work that has to stop the recording(Time change, File delete, HDD connect/disconnect  
etc.) is performed during the recording, the current recording stops.  
7-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-3  
SHR-2040/2041/2042 USER’S MANUAL  
Eve n t Re co rd in g  
3
■
Alarm Detection  
Sensor operation mode in Alarm of Event Record menu shall be set to N.O (Normal Open)  
or N.C (Normal Close).  
■
■
■
Motion Detection  
Motion detection in the Event Recording menu shall be set to On.  
Video Loss Detection  
Video Loss in Event Record menu shall be set to On.  
Event Recording Mode  
Sets the recording type when an event occurs. In particular, depending on  
PreAlarm Off or PostAlarm Off, PreAlarm or PostAlarm Recording is disabled  
respectively.  
Warning  
If the work that has to stop the recording(Time change, File delete, HDD connect/disconnect  
etc.) is performed during the recording, the current recording stops  
7-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-4  
Ch a p te r 8  
Se a rch a n d Pla y  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-1  
SHR-2040/2041/2042 USER’S MANUAL  
Be fo re Use  
■
■
■
■
■
■
■
Pressing the “SEARCH” button shows Search Menu on the screen as seen above.  
Calendar Search searches a video file by the use of a calendar at the desired time.  
Event Search searches a video file recorded by the occurrence of event.  
Date/Time Search searches a video file by the entering of a day and time.  
“Go To First” searches a video file from the oldest one.  
“Go To Last” searches a video file from the latest one.  
Backup Search searches backed-up video file.  
- Searches the backup video of backup device connected with the set.  
Note  
During Event Recording, the Search or Play button has no power to let you enter the Search  
mode. On entering the Search mode, ( ) will appear.  
8-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-2  
Ca le n d a r Se a rch  
1
■
■
■
■
■
■
■
■
Be sure to select both the channel and the date to search. And press the [Start] button to  
search for the desired time.  
Use a calendar to search the video file of desired time. Four channels in maximum are in  
the range of search.  
Select the channel up to 4 by the use of ¦, ‹ and Enter button. And then the date column  
will be displayed in thick blue when it has a video recorded in the channel.  
Use the ¦, ‹¤button until you reach the Year/Month setup line and use both buttons and  
the “Enter” button to select Year/Month.  
If you select a day by the [Enter] button, a checkbox will appear on the right of the date  
number and the checkbox will be checked.  
Use the ƒ button until you reach the Time bar and move to the time you want with the  
¦, ‹ button, and then press the Enter button to select a time.  
If you want to start the search, press the [Start] button. And press the [CANCEL] button to  
move to the previous menu.  
You are able to search every 30 minutes.  
8-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-3  
SHR-2040/2041/2042 USER’S MANUAL  
Eve n t Se a rch  
2
■
Searches Normal Recording, Schedule Recording, Alarm Recording, Motion Recording, and  
V.Loss(Video Loss) Recording by the time.  
■
■
You shall select a channel to search to see the event information of the channel.  
On the basis of event information for each channel, the system searches a video file for the  
event. Only one channel is allowed for video search.  
■
■
■
If you use both the [Enter] button and the ¦, ‹¤button key to select a channel, the system  
will show the list of event for the selected channel only.  
After channel selection, you can use the ¦, ‹¤[Enter] button to select an event out of the  
list. The checkbox on the left of the selected event number will be checked.  
If you want to start the search, use the ƒ¤button until you reach [START] and press the  
[Enter] button. If you want to cancel the search, move to the [Exit] and press the [Enter]  
button. If you wish to view the event list of the next screen, select [NEXT] and press the  
[Enter] button and if you wish to view the event list of the previous screen, select [PREV]  
and press the [Enter] button.  
8-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-4  
Da te / Tim e Se a rch  
3
■
■
■
Use the Day/Time information to search a video file at the time as you desire. Up to 4  
channels can be searched at once.  
After you select a channel with the œ, ƒ, [Enter] button, the checkbox on the right of  
selected event number will be checked.  
Use the ƒ button until you reach the Search Time setup line. Press the [Enter] button to  
change the search time. Search Time change will be done by the  
Year/Month/Day/Hour/Minute/ Second unit with the œ, ƒ, button. For your convenience,  
you may hold on a key to change the value continuously.  
■
■
If you want to start the search, use the ƒ button until you reach [START] and press the  
[Enter] button. If you want to cancel the search, move to the [CANCEL] and press the  
[Enter] button.  
The time information, 2005-03-10 08:38:58 on the bottom left corner, represents the time  
when play starts.  
8-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-5  
SHR-2040/2041/2042 USER’S MANUAL  
Go to First Se a rch  
4
■
■
■
Searches the oldest one among recorded video files. Up to 4 channels can be searched at  
once.  
After you select a channel with the œ, ƒ, [Enter] button, the checkbox on the right of the  
selected channel number will be checked.  
Press the [Start] button want to start the search and to cancel. And press the [Cancel]  
button to cancel the search.  
8-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-6  
Go to La st Se a rch  
5
■
■
■
■
Searches the latest one among recorded video files. Up to 4 channels can be searched at  
once.  
After you select a channel with the œ, ƒ,[Enter] button, the checkbox on the right of the  
selected channel number will be checked.  
Press the [Start] button want to start the search and to cancel. And press the [Cancel]  
button to cancel the search.  
If you start Go To Last Search during recording, the system will search the video image right  
at the time of entering Search.  
8-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-7  
SHR-2040/2041/2042 USER’S MANUAL  
Ba ck u p  
6
■
■
■
■
■
■
■
First, select the backup device.  
Mark the data of device.  
Select the file name to backup, and the detail information of a file is displayed in the below.  
The [Previous] button shows the previous page.  
The [Next] button shows the next page.  
The [Start] button plays the desired file.  
The [Exit] button exits the menu.  
Note  
SHR-2042 supports the internal CD-R/W.  
8-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-8  
Pla y b a ck  
7
‹ ꢀ¤  
■
Press the PLAY/PAUSE button(  
) to play the data recorded in HDD.  
II  
■
If you used the SEARCH button for playback just before, the system would remember the  
information of the played channel until you click the PLAY/PAUSE button( ‹ ꢀ¤ ) again,  
then the system plays the previous channel.  
If you press the PLAY/PAUSE button(  
never tried the playback.  
II  
‹ ꢀ¤  
), the Search Menu will appear as far as you  
II  
Note  
Pressing the PLAY button( ‹ ꢀ¤ ) does not affect the playback as far as the user stays in the  
II  
MENU. Be sure to exit from the MENU to start the playback.  
■
■
Press the STOP button(  
) to stop the playback. If you press the Playback/PAUSE  
‹ ꢀ¤  
button(  
) once more, the recording will resume from the point where the previous  
II  
recording stops. When the data position reaches the end of HDD during the playback, the  
playback will be paused.  
8-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-9  
SHR-2040/2041/2042 USER’S MANUAL  
■
Definition Play Screen Mode  
PIP Screen  
Single Screen  
4 Split Screen  
6 Split Screen  
9 Split Screen  
■ 4 Split Screen : If you select more than a channel, 4 Split Screen will appear.  
■ Single Screen : This appears when you select one channel in Search. If you press the  
[CH1~CH4] button in the other split screen, the selected channel appears  
with the single screen. If you press the ZOOM button in the single screen, the  
selected area will be enlarged by twice. And you can move the zoom area by  
the use of direction key.  
■ PIP Screen :  
If you press the Mode button while the single screen plays, PIP Screen will  
appear(The large screen displays the channel in play while the small screen  
on the bottom right corner displays a Live channel in PIP type). Use the UP  
and DOWN key to move small PIP screen (Live Channel) vertically. If you  
press the [ENTER] button, a blue bar will appear in the live screen and if you  
press the Channel button, you will be able to turn to the channel selected by  
the live screen.  
■ 6 Split Screen : If you press the Mode button in the single screen, 6 split screen will appear.  
The single screen in playing is displayed at the top of right, and the 4 live  
screens are displayed at the bottom of left.  
■ 9 Split Screen : If you press the Mode button in the 4 split screen, 9 split screen will appear.  
The 4-split screen in playing is displayed at the top of right, and 4 live  
screens are displayed at the bottom of left.  
8-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-10  
■
■
Play at Faster Speed  
If you press the LEFT or RIGHT button(  
able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or  
reversely.  
‹‹  
¦¦  
/
) during the playback, you will be  
Viewing Still Screen  
¦¦  
‹‹  
If you press the LEFT or RIGHT button(  
/
) when the system paused, you will  
be able to see still screens forwardly or reversely.  
During the reverse search, the interval between cuts becomes long depending on the  
recording specification.  
■
Audio On/Off  
If you press the [Audio] button in other screen than 4 Split Screen(i.e. Single Screen, PIP  
Screen, and 9 Split Screen), you will be able to turn Audio of the playback channel on or off.  
In 4 Split Screen, Audio is not activated.  
8-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9  
Ch a p te r 9  
Sm a rt Vie w e r  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-1  
SHR-2040/2041/2042 USER’S MANUAL  
In tro d u ctio n  
1
Smart Viewer is a program that a general PC user is able to install  
SHR-2040/2041/2042 to his PC to monitor the video and audio data in the real time  
through network without going to the site where SHR-2040/2041/2042 is installed.  
9-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-2  
Fe a tu re  
2
●
●
●
Thanks to the transmission of video data compressed by the MPEG-4 Video  
Compression method, it can play the video images of good quality.  
Thanks to the G.726 Voice Compression method, it supplies the voice data of  
good quality. Use of armored MIC improves the quality of remote voice.  
Thanks to the transmission of video/audio stream through RTP(Real-Time  
Transport Protocol), the real-time video playback is excellent and multi-users’  
simultaneous connection does not affect the transmission speed in whole abruptly.  
●
Command & Control by RTSP(Real-Time Streaming Protocol) enables safety  
control through the network.  
●
●
Variable transport protocols are supported (TCP/IP, UDP(Unicast, Multicast)).  
Connection is open to you at any time to monitor video and audio data by inputting  
IP Address only.  
●
You can not only perform real-time recording(*.dvr format) with User’s PC whereas  
necessary during the monitoring but also convert recorded video files(*.dvr format)  
into frame unit images((JPEG format).  
●
●
●
Up to 3 Smart Viewer users are allowed to connect to a DVR simultaneously.  
(If the multicast is used, up to 6 users can connect.)  
With a Smart Viewer, you are allowed to connect to as many as 9  
SHR-2040/2041/2042s to monitor them simultaneously.  
Smart Viewer is optimized in the resolution of 1024X768.  
9-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-3  
SHR-2040/2041/2042 USER’S MANUAL  
PC Specifica tion(Recom m enda tion)  
3
●
OS : Win98SE, WinMe, Win2000, WinXP  
●
Recommendation :  
CPU Pentium 3 1GHz or higher  
RAM 256 MB or higher  
VGA RAM 32Mb or higher  
DirectX 8.1 or higher  
Note  
Depending on Recording Rate, Video Size, and user’s PC specification set to  
SHR-SHR-2040/2041/2042, the number of Smart Viewer playback frame varies.  
For the detailed specification, refer to Appendix 5.  
9-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-4  
Sm a rt Vie w e r In sta lla tio n  
4
Smart Viewer Installation  
●
Put a Smart Viewer Program CD in CD-ROM and open the “Smart Viewer” folder  
in the CD.  
●
Run the “Setup.exe” file.  
9-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-5  
SHR-2040/2041/2042 USER’S MANUAL  
●
Click the “Next” button.  
●
If you agree with Smart Viewer License, click “Yes”.  
●
Designate a folder to install Smart Viewer in it and click “Next”.  
9-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-6  
●
The system proceeds with setup file installation and system setup.  
●
Installation is complete. Click the “Finish” to terminate the installation.  
9-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-7  
SHR-2040/2041/2042 USER’S MANUAL  
Sma rt View er Progra m Execution  
5
●
Double-click the Smart Viewer icon in the background screen to run the program.  
9-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-8  
Sm a rt Vie w e r In itia l Scre e n  
6
●
Screen Description  
2
1
3
4
6
5
7
8
11  
10  
9
12 13 14  
!
This is the button to enter the Search mode in which you can search and play  
remote the video file recorded in SHR-2040/2041/2042 and enter the Monitoring  
mode for real-time video monitoring.  
@
#
$
This button terminates or minimizes the program.  
It displays the current date, day, and time.  
This button is used for the connection with the preset DVR(SHR-2040/2041/2042) or  
site.  
%
^
This screen shows the monitoring video.  
These buttons select the window displays the event message and the window  
displays the connection condition of camera.  
&
*
(
This window displays the event message from SHR-2040/2041/2042 in the real-time.  
These buttons display the status of current channel.  
These buttons adjust the audio volume and video brightness/contrast, and save the  
video file.  
)
1
These buttons are used for PTZ related functions.  
These buttons are used for screen split and Sequence Mode.  
2
3
4
This button is used for the connection Callback.  
This button is used for Favorite function when connecting to the site.  
This button pops up the Setup Mode window to change Smart Viewer or  
SHR-2040/2041/2042 setup. (Refer to 9-30. Setup Mode.)  
9-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-9  
SHR-2040/2041/2042 USER’S MANUAL  
Mo n ito rin g Mo d e  
7
●
DVR(SHR-2040/2041/2042) / SITE Connection  
- Select the name of DVR(SHR-2040/2041/2042) or site for connection and click  
the connection button.  
Note  
You can set the name, IP, and password of DVR(SHR-2040/2041/2042) for  
connection in the Setup mode. Also, the site setup which permits simultaneous  
connection to multi-DVRs(SHR-2040/2041/2042) is available in the Setup mode.  
You are allowed for the simultaneous connection with no more than 9  
DVR(SHR-2040/2041/2042) as you approaches at the site.  
ꢀ Connection Failure Cases  
1. Password Certification Failure  
- In case of discord between the Network password set to SHR-2040/2041/2042  
and the connection password set to Smart Viewer, a window pops up to induce  
retry of password input.  
2. Admin User Connection Failure  
- Where SHR-2040/2041/2042 that you wish to connect to has been already  
occupied by other user in an Admin authority, you are authorized with access to  
SHR-2040/2041/2042 concerned in a User authority.  
9-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-10  
Note  
No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to  
access SHR-2040/2041/2042 simultaneously.(In the case of multicast, 5 User authorized users  
are allowable.)  
Caution  
Once occupied by 3 users( In the case of multicast, 6 users), SHR-2040/2041/2042  
does not permit more connection.  
●
Monitoring Mode Connection Screen  
Note  
When connecting with SHR-2040/2041/2042 in the 9-split mode setup, the setup, the setp is  
changed to the 4 split mode and 4 split screen is show After the connection, you can change it  
to the 9 split mode.  
Caution  
If you change the “Video size” or “Color Quality” from the setup tab of [Display  
Registration Information] while Smart Viewer is running, Smart Viewer will fall into  
an unexpected condition.  
You should terminate the Smart Viewer first to change them.  
●
Mode Conversion Button  
- This button converts the monitoring mode and the search mode.  
9-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-11  
SHR-2040/2041/2042 USER’S MANUAL  
●
Time Information  
- As soon as you are connected to SHR-2040/2041/2042, the current date, day, and  
time of SHR-2040/2041/2042 will be displayed.  
- Otherwise, the current date, day, and time of your PC will be displayed.  
●
Connection Information  
- As soon as you are connected to SHR-2040/2041/2042, the connection button  
will display connection status.  
- If you click the connection button here, connection will be cancelled.  
●
Play Screen OSD Information  
2
3
1
4
6
5
!
@
Channel no., camera name, and video size will be displayed.  
Video Size : (C)CIF / (N)Normal / (L)Large  
If the Video data of the current channel are recorded in your PC, REC mark is  
displayed.  
#
$
%
^
Audio ON/OFF Button is displayed.  
The name and IP address of SHR-2040/2041/2042 in connection are displayed.  
The current channel alarm status is displayed.  
The controllability of the current channel PTZ is displayed.  
9-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-12  
Note  
# Clicking the speaker icon turns the audio of channel on or off.  
: Audio OFF : Audio ON  
If you turn the audio of a SHR-2040/2041/2042 channel off, “Disable” will be  
displayed.  
: Audio Disabled  
● For the Audio on channel now, use the following audio button to adjust the  
volume and set the mute.  
Note  
% the alarm or motion detection occurs at the channel of SHR-2040/2041/2042,  
which is set to alarm or motion detection, it is displays on the screen in the  
real-time with an icon.  
: Motion Detection  
: Alarm Event  
Note  
^ If you connect and set up PTZ Camera in SHR-2040/2041/2042, PTZ  
controllability for the channel will be displayed.  
● Select a channel capable of PTZ and use the PTZ button at the bottom to  
control PTZ. (Refer to the description of PTZ button.)  
9-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-13  
SHR-2040/2041/2042 USER’S MANUAL  
●
Event Log Display Window  
- Click the Log button to activate the log display window.  
- It displays the event(alarm, user connection, and setup change) occurring at  
SHR-2040/2041/2042 in the real-time.  
Note  
[Event Message]  
‹ Connecting.. : Trying to connect to SHR-2040/2041/2042.  
‹ Connected.. : Succeeded connecting to SHR-2040/2041/2042.  
‹ Connection Failed : Failed in connecting to SHR-2040/2041/2042.  
‹ Disconnected.. : Finished connecting to SHR-2040/2041/2042.  
‹ Setup(Remote) : SHR-2040/2041/2042 setup at Dvr Setup of Viewer changed.  
‹ Setup Start / End (Local) : Start/Finish the Menu screen at SHR-2040/2041/2042.  
‹ Video Loss CH[N] : Video Loss at the N channel of SHR-2040/2041/2042  
encountered.  
‹ Alarm Detection CH[N] : Alarm issued at the N channel of SHR-2040/2041/2042.  
‹ Motion Detection CH[N] : Motion detected at the N channel of SHR-2040/2041/2042.  
‹ Time Change : Date/Time of SHR-2040/2041/2042 changed.  
‹ Load Factory Default : SHR-2040/2041/2042 System initialized.  
‹ Network Change : SHR-2040/2041/2042 Network setup changed.  
‹ System Shutdown : SHR-2040/2041/2042 System terminated.  
‹ Hdd Format : SHR-2040/2041/2042 HDD initialized.  
‹ Disk Full : No more space in SHR-2040/2041/2042 HDD.  
‹ Power Failure Recovery : SHR-2040/2041/2042 resumed after power failure.  
‹ Backup Start/End/Fail/Stop : Backup at SHR-2040/2041/2042  
started/finished/failed/stopped.  
‹ Network Traffic Busy : Data transport in the network is not smooth.  
‹ Access Denied(Limit Over) : Over connection.  
9-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-14  
Caution  
When Time Change, Load Factory Default, Network Change, System Shutdown, or  
Hdd Format event occurs, Smart Viewer terminates the connection automatically.  
●
Camera connection Indication Window  
- Displays the connection condition of DVR and CAMERA in the list.  
Note  
[DVR Icon Color]  
‹ Successfully connected to SHR-2040/2041/2042, the icon turns yellow, otherwise,  
turns black.  
[DVR Icon Color]  
‹ Connected to CAMERA for monitoring, the icon turns yellow.  
‹ Connectable, the icon turns blue, otherwise, turns black.  
9-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-15  
SHR-2040/2041/2042 USER’S MANUAL  
●
Screen Split Selection Button  
- Small Sized Single / Single / Quad / Nine-Split Mode Sixteen-Split Mode  
- You can change the Split Mode of the screen under monitoring.  
●
Sequence Mode Button  
- Changes the channel to be played at the preset interval.  
- The sequence time interval can be set at the Setup Mode?Viewer Setup.  
- In Single Mode : 1 ● 2 ● 3 ● 4 ● 1 (CH)  
- In Quad Mode : 1,2,3,4 ● 1,2,3,4 (CH)  
- In Nine-Split Mode : 1,2,3,4 -> 1,2,3,4(CH)  
- In Sixteen-Split Mode : 1,2,3,4 ● 1,2,3,4 (CH)  
Note  
If you connected with multi-DVRs(SHR-2040/2041/2042) through a site, the sequence will  
operate as follows.  
- In Single Mode : DVR1:3CH ●...● DVR1:4CH ● DVR2:1CH ●...● DVR1:1CH  
- In Quad Mode : DVR1:1,2,3,4CH ●...● DVR2:1,2,3,4CH ● ... DVR3:1,2,3,4CH  
- In Nine-Split Mode : DVR1:1,2,3,4CH ● DVR2:1,2,3,4CH ●... DVR3:1,2,3,4CH  
- In Sixteen-Split Mode : DVR1:1,2,3,4CH ● DVR2:1,2,3,4CH ● DVR3:1,2,3,4CH  
●
Monitoring screen condition Information / Selection Button  
- Displays the Split or Monitoring condition of the screen in play.  
9-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-16  
: When monitoring with Quad Mode  
: When monitoring with Single Mode  
: Camera Off  
Note  
The number in the screen icon indicates the screen position in SmartViewer.  
: The orange icon indicates the current channel is connected to a camera.  
: The gray icon indicates the current channel is connected to a camera but not  
displayed in the screen.  
: The black icon with a slash indicates the current channel is not connected to any  
camera.  
9-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-17  
SHR-2040/2041/2042 USER’S MANUAL  
●
NEXT Button  
-
Click the NEXT(Mouse Left Button) to see the channel next to the current channel.  
- In Single Mode : 1 ● 2 ● 3 ● 4 ● 1 (CH)  
- In Quad Mode : 1,2,3,4 ● 1,2,3,4 (CH)  
- In Nine-Split Mode : 1,2,3,4 ● 1,2,3,4 (CH)  
- In Sixteen-Split Mode : 1,2,3,4 ●1,2,3,4 (CH)  
Note  
If you connected with multi-DVRs(SHR-2040/2041/2042) through a site, the  
sequence will operate as follows.  
- In Single Mode : DVR1:3CH ●...● DVR1:4CH ● DVR2:1CH ●...● DVR1:1CH  
- In Quad Mode : DVR1:1,2,3,4CH ●...● DVR2:1,2,3,4CH ● ...  
- In Nine-Split Mode : DVR1:1,2,3,4CH ● DVR2:1,2,3,4CH ●DVR3:1,2,3,4CH ...  
- In Sixteen-Split Mode : DVR1:1,2,3,4CH ● DVR2:1,2,3,4CH ●DVR3:1,2,3,4CH ...  
●
CALLBACK Button  
- If you press CALLBACK, the CALLBACK window will be activated to receive  
messages.  
- Receiving a message, Smart Viewer automatically tries to contact a DVR.  
- In the event of Video Loss, Alarm, or Motion Detection, a message is received.  
9-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-18  
●
FAVORITE Button  
- If you press FAVORITE, the FAVORITE window will be activated.  
a
a
If you click the current FAVORITE, the cameras saved in  
the current setting value will be displayed in the screen.  
You may delete the selected FAVORITE or all FAVORITE  
setting values.  
b
b
c
c
You may set up a new FAVORITE number and name.  
Change FAVORITE at the set intervals.  
d
d
Note  
- The FAVORITE button is available only when you contact SITE.  
- The FAVORITE information setting value is saved in the Config file even after you are  
away from the SITE.  
- If you change the DVR list composing the SITE from Setup, the FAVORITE setting value  
will be initialized  
9-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-19  
SHR-2040/2041/2042 USER’S MANUAL  
●
Video Recording Button  
- If you select a channel in the playback and click the “Save” button, the video will  
be saved in a file format with the extension of *.dvr in a designated folder of your  
PC.  
- The name of the directory in which an image will be saved, the file name, and the  
image save length shall be set up at the Setup Mode ● Viewer Setup.  
- The video length to be saved can be set from one minute to 10 minutes.  
- The saved video can be played in the Local mode of Search mode.  
- Click the button again to stop recording. However, manual suspension is prohibit-  
ed for 10 seconds after recording started.  
●
Audio Volume Control Button  
- You can control the audio volume of channel in the playback or set to mute for it.  
- You can adjust the audio volume from 0 to +10.  
●
Video Brightness/Contrast Control button  
- Select the channel in the playback and use the control button(+,-) to adjust the  
brightness or contrast of video.  
- The default value is set to +5.  
- You can adjust the brightness or contrast from 0 to +10.  
- Press the  
button to recover the default value.  
Note  
The adjusted Audio volume, brightness, and contrast values will be saved in your PC  
and remain unchanged even if you terminate Smart Viewer and restart it.  
* OS of Windows 98 or ME do not support this Brightness/Contrast function.  
9-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-20  
●
PTZ Camera Control Buttons  
- Select a channel connected to PTZ Camera to control PTZ related functions.  
- PAN Left / Right  
- TILT Up / Down  
- Diagonal Control  
- The channel under PTZ control will be displayed in the center of the button.  
3
1
2
!@ ZOOM IN / OUT  
# POWER ZOOM : Click P button to activate POWER ZOOM.  
- POWER ZOOM is a function to zoom in or zoom out the video screen by clicking the  
screen.  
- After POWER ZOOM is dominant, ZOOM IN / OUT will zoom in or out the video  
screen.  
- POWER ZOOM Operation Procedure : Click POWER ZOOM ● Select ZOOM IN or  
OUT ● Click ZOOM IN or OUT zone in the video screen ● ZOOM IN / OUT will be  
activated in the clicked zone.  
Note  
The PAN / TILT / ZOOM function is supported to all the cameras.  
But, POWER ZOOM is supported only by Samsung Smart Dome Camera, and  
assured to the operation of TILT below 45°.  
1
4
3
2
9-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-21  
SHR-2040/2041/2042 USER’S MANUAL  
! PRESET  
- If you press the PRESET button, a window for PRESET setup pops up.  
a
If you click the current PRESET number and  
name, the camera will move to its position.  
a
b
b
You can delete the selected or all the  
PRESET setup values.  
c
c
You can set a new PRESET number and  
name.  
Note  
! The PRESET function is supported to all the cameras.  
You are allowed to set no more than 20 PRESET items.  
But, the AD Protocol camera can be set up to 7 PRESET items.  
@ AUTOPAN : The camera operates reciprocating between Start and End.  
# SCAN : The camera operates circulating the PRESET setup positions.  
$ PATTERN : The camera operates following the route that user defined.  
Note  
The name of @,#, and $ functions varies depending on the camera and some  
cameras do not support these functions.  
- The Samsung camera supports all the functions and names.  
- The Panasonic camera supports all the functions, but with different names.  
@ SEQUENCE # AUTOPAN $ SORT  
- The PELCO camera supports all the functions, but with different names.  
@ FRAME SCAN # AUTO SCAN $ PATTERN  
- Other cameras do not support the @AUTOPAN, #SCAN, and $PATTERN  
functions.  
9-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-22  
●
Self Menu Setup of PTZ device  
1
! You can set the function menu in the PTZ camera.  
1
2
3
! This is a Menu screen supplied by the camera itself, seen from Viewer.  
@ Use the ꢁ/ꢂ/ꢃ/ꢄbutton for the movement between menus.  
# This is a button for the role of Enter.  
Note  
The Camera Menu Setup function is supported by Samsung and Panasonic camera  
only.  
Caution  
As far as SHR-2040/2041/2042 uses the PTZ camera control functions, Smart Viewer  
can not control PTZ Camera.  
The PTZ Camera control functions can be used by the user with Admin  
authority.  
9-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-23  
SHR-2040/2041/2042 USER’S MANUAL  
Se a rch Mo d e  
8
●
The initial screen of search mode  
- The search mode is divided into the remote mode to search and play the  
SHR-2040/2041/2042 video and the local mode to play *.dvr file saved in the  
directory designated by your PC.  
1
3
4
2
5
6
7
8
10  
11  
9
12  
!
To change to the search mode for the remote control of video recorded in  
SHR-2040/2041/2042.  
@
#
To show the playback video.  
To change to the remote mode for the transmission of video recorded in  
SHR-2040/2041/2042 through network.  
$
%
^
&
*
(
)
1
To change to the local mode for the playback of *.dvr files recorded in your PC.  
Calendar window to select “Year/Month/Day” for search.  
To control the audio volume and video brightness/contrast.  
To change the screen split.  
Button for the Record / Convert File / Print / Setup functions.  
To control the playback of searched video.  
To display the next channel in order.  
To change the channel and DVR or renew the calendar window  
and Time Line.  
2
Timeline to display the time information of search date recorded in  
SHR-2040/2041/2042.  
Note  
- When connecting to the site, select a DVR to search in the camera connection list.  
- When connecting as a user, you are denied to access the search mode.  
9-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-24  
●
DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE  
- Same as “DVR(SHR-2040/2041/2042)/SITE Connection” of the monitoring mode.  
●
DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE  
- Select SHR-2040/2041/2042 from the Contact list.  
- SHR-2040/2041/2042 turns black if contacted with the ADMIN authority and  
turns gray if contacted with the USER authority.  
- Without the ADMIN authority, search is not accessible.  
●
Remote Mode  
- This mode transfers the video data recorded in SHR-2040/2041/2042 by network  
for the playback.  
- Up to 4 channels are allowed for simultaneous search and playback.  
- The video information at the time indicated by the timebar will be displayed in the  
playback screen.  
When clicking, it changes to the remote mode.  
9-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-25  
SHR-2040/2041/2042 USER’S MANUAL  
●
Calendar Window  
- If the video data in on-line SHR-2040/2041/2042 was recorded, the date  
turns red.  
- If you click the date in red, the saved video information is displayed.  
- The currently selected date will be marked with a thick red box.  
- ¦¤: Moves to the previous month.  
- ‹¤: Moves to the next month.  
●
Audio Volume Control, Video Brightness/Contrast Control Buttons  
- Same as the control function of Monitoring Mode  
- Windows 98 or ME does not support this Brightness/Contrast function.  
●
Screen Split Selection Button  
- Small Sized Single / Single / Quad / Nine-split/ Sixteen split mode  
Note  
In the remote mode, Nine-split Mode is not available and in the local mode, Quad,  
Nine split Mode is not available.  
●
Video Save(Backup) / Video Conversion / Print / Setup  
1
2
3
4
! Video save button  
:During the playback(Play/Reverse Play/Fast Forward/Fast Backward),  
- If you select a channel in the playback and click the SAVE button, the video is  
saved in a file format with the extension of .dvr in a designated folder of your PC.  
*
- The directory in which an image will be saved, the file name, and  
the video length to be saved can be set at the Setup Mode  
●
Viewer Setup.  
- The video length to be saved can be set from one minute to 10 minutes.  
- Click the button again to stop recording. However, manual suspension is  
prohibited for 10 seconds after recording started.  
9-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-26  
@ Backup Button  
- If not playback(Stop), the video save button performs the backup function.  
- If the save button is pressed, the window for backup pops up.  
- Set a Start/End tome for backup and select a file format to save.  
- The backup starts when the “Start” button is clicked. The backup file is saved  
according to the setting route; Setup ● Viewer Setup ● Video Recording ●  
Video Location.  
- To stop the backup, click the “Stop” button.  
Note  
Video saving in the remote mode is available only when the Play/Reverse  
Play/Fast Forward/Fast Backward button remains pressed down..  
The backup function in the remote mode is available at the Stop status.  
# File Converting Button  
- This function converts .dvr files into “ .jpg” files.  
*
*
- Click the “Open” button to select a .dvr file to be converted.  
*
- Select the JPEG Frame or AVI Video.  
- If the JPEG Frame is selected, the file is converted into the “ .jpg” file by  
*
clicking the “Start” button. The converted “ .jpg” file is saved according to the  
*
setting route Setup ● Viewer Setup ● File Converting ● Jpeg Location.  
- I f the AVI Video is selected, the file is converted into the “ .avi” file by clicking  
*
the “Start” button. The converted “ .avi” file is saved according to the setting  
*
route Setup ● Viewer Setup ● File Converting ● AVI Location  
- Press the “Start” button to convert it to a .Jpg file. Press Setup ● Viewer  
*
Setup ● File Converting to save the converted .jpg file.  
*
- Click the Stop button to pause the file conversion.  
9-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-27  
SHR-2040/2041/2042 USER’S MANUAL  
$ Print  
- This function outputs the screen zone of the playback video which is now  
being displayed.  
% Setup Mode Button  
- This button pops up the setup mode window.  
●
Play Buttons  
2
1
5
9
3
4
8
7
6
! Play : Play  
@ Reverse Play : Reverse Play  
# Stop : Stop  
$ Fast Forward : Faster Play  
% Fast Backward : Faster Reverse Play  
^ Step Forward : Forward playback per second.  
& Step Backward : Reverse playback per second.  
* Go to First : Playback of the first image in the time Line  
( Go to Last : Playback of the latest(last) image in the time Line  
9-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-28  
Note  
During the play(Play/RevPlay/FF/FB), disconnection or change to the both monitor-  
ing mode and local mode is not permitted. Click the Stop button first before the  
change.  
●
Time Line  
- Displays the time information of video in SHR-2040/2041/2042 selected on the  
calendar window.  
- The normal mode indicates the time information of 24 hours while the  
Extension mode indicates the time information every 2 hours.  
2
1
3
[ Normal mode ]  
! The channels being displayed in the playback screen will be activated in the white  
background.  
@ Time Line : The time information of video recorded in SHR-2040/2041/2042P.  
# Time Bar : Displays the current time of video being displayed in the playback screen.  
Note  
Double click the area closed by the time bar to change to the zoom in mode.  
One column of time line represents an hour.  
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),  
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.  
2
1
[ Zoom In Mode ]  
! Displays the time line one hour ago.  
@ Displays the time line one hour later.  
Note  
Double click again the area closed by the time bar to change to the normal mode.  
One column of time line represents 5 minutes.  
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),  
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.  
9-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-29  
SHR-2040/2041/2042 USER’S MANUAL  
●
Next Button  
- Changes the channel as the Next button does in the monitoring mode.  
Note  
During the video playback(Play/RevPlay/FF/FB), the channel change is not available.  
●
●
Reload Button  
- Updates the record time information in the calendar window and time line.  
Local Mode  
- Plays *.dvr file saved in the directory of your PC by the Record function.  
- You can search and play only one channel.  
- You are allowed to access it regardless of connecting with SHR-2040/2041/2042.  
- Other functions than the calendar display function are as same as those of  
the remote mode.  
- The time information of LocalFile will be displayed at the first channel position in  
the time line together with the file name.  
: Selects a file to be played in the file selection window and changes  
to the local mode.  
Note  
Only the *.dvr file saved by the audio activation can be played in the local mode.  
9-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-30  
Se tu p Mo d e  
9
●
Initial Screen  
3
1
2
4
! Button to select items for DVR Setup, Viewer Setup, Site Setup, and  
S/W Version setup.  
@ It shows what the selected Setup item can set up in detail.  
# button to terminate the setup window.  
$ Button to save the information revised in the setup window, remark the information  
prior to such a revision, or terminate the setup window.  
9-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-31  
SHR-2040/2041/2042 USER’S MANUAL  
●
Setup Item Selection Button  
- It is used for the selection of each setup item.  
- It is composed of 4 items- DVR Setup, Viewer Setup, Site Setup, and S/W  
Version.  
- DVR Setup: Allows you to change the remote menu setup items of  
SHR-2040/2041/2042.  
- Viewer Setup : Allows you to set the various kinds of item concerning the  
operation of Smart Viewer.  
- Site Setup : Allows you to set SHR-2040/2041/2042 information, that is  
SHR-2040/2041/2042 name, IP Address, ID, and Password that you are going to  
contact through Smart Viewer or registers all the registered  
SHR-2040/2041/2042s at a site for control.  
- S/W Version : Shows the current version of Smart Viewer, system  
requirement, and the System S/W version of on-line SHR-2040/2041/2042 and  
upgrades SHR-2040/2041/2042 System S/W remotely.  
●
Save/Cancellation of Revised Information  
- Click the [Apply] button to save the information revised in the setup window and  
click the [Cancel] button to display the information before such a revision.  
●
Closing the setup window  
- Click the [X] icon on the top of right corner in the setup window or click the  
[Close] button to close the setup window.  
- If more than one setup item have been revised before you close the setup  
window, the following message box pops up. If you press OK, the revised  
information will be saved, closing the setup window but if you press CANCEL,  
the revised information will be flown away, closing the Setup window.  
9-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-32  
DVR Setup  
- Click the [DVR Setup] button for DVR Setup.  
- You can change remotely the setup items of SHR-2040/2041/2042 Menu, being  
connected with Smart Viewer.  
- DVR Setup is composed of 5 items; System, Camera/Audio, Monitoring,  
Recording, and Network.  
Note  
- You are authorized with access to DVR Setup in an Admin authority only.  
- The button will not be activated if you are connected to  
SHR-2040/ 2041/ 2042 as a user or unconnected.  
1
2
SHR204X-V1.0.0-20050701080722  
! Among more than one SHR-2040/2041/2042 that is connected now, the name of  
SHR-2040/2041/2042 connected in the Admin authority will be listed. Depending  
on connecting to a SHR-2040/2041/2042 or the site, the name of SHR-  
2040/2041/2042 or the name of SHR-2040/2041/2042 connected in the Admin.  
Authority among those composing the site will be listed. You can select one to set  
SHR-2040/2041/2042 Menu.  
@ To display the setup menu for selected SHR-2040/2041/2042.  
9-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-33  
SHR-2040/2041/2042 USER’S MANUAL  
●
Detailed DVR Setup Items  
! System  
- Information  
Information shows the information on on-line SHR-2040/2041/2042.  
SHR204X-V1.0.0-20050701080722  
Note  
For the detailed items of DVR Setup, refer to Chapter 5.  
- Password  
Sets the password for the control of SHR-2040/2041/2042 Menu or  
SHR-2040/2041/2042 key input.  
9-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-34  
Caution  
System Password shall be composed of numeric only, up to 8 digits.  
Note  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supported at the System Password input.  
- Use the BACKSPACE key to delete the contents.  
Note  
Default System Password is set to 4321.  
- Date/Time  
Data/Time is used to set the information of Date, Time, Format, and DST for  
on-line SHR-2040/2041/2042.  
Note  
- If you change the Data/Time value, SHR-2040/2041/2042 automatically cuts the  
connection with Smart Viewer to apply the new time setup.  
- Upon completing the new time setup for SHR-2040/2041/2042, you are permitted  
to resume the connection with the Smart Viewer.  
- But, Display Format or DST can be set without the disconnection.  
9-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-35  
SHR-2040/2041/2042 USER’S MANUAL  
- Language  
Language sets the language in which on-line SHR-2040/2041/2042 will be  
expressed  
Note  
The change of language by the system language results in the change of language  
expression setup of SHR-2040/2041/2042. In short, the language setup of Smart  
Viewer does not change.  
Language specification to be supported is subject to change later.  
- Disk Mode  
In Disk Mode, you can set the writing mode of HDD installed to  
SHR-2040/2041/2042.  
9-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-36  
- Remocon (Remote Control Device)  
Remocon can set the remote control device installed to SHR-2040/2041/2042.  
Note  
If you install the remote control device to the main body of SHR-2040/2041/2042  
and activate the setup, PTZ control is not available in the Viewer.  
9-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-37  
SHR-2040/2041/2042 USER’S MANUAL  
@ Camera  
- Config.  
Config. sets Video, Audio On/Off, Camera Title, and Auto Sequence Time  
for each channel of on-line SHR-2040/2041/2042.  
Caution  
- Only English is supported for the title. If you type in and apply the title in your  
native language, warning message pop sup to ask your retyping.  
- The title should be composed of no more than 15 digits.  
- If you leave the title blank and apply it, Warning message pops up to ask  
your retyping.  
Note  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supported for title input.  
- Use the BACKSPACE key to delete the contents.  
9-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-38  
- PTZ device  
It sets Camera ID, Protocol, Baud Rate, Parity, Data Bit, Stop Bit, and Serial  
Mode when connecting the dome camera to all the channels.  
# Monitoring  
- Monitoring  
It sets both the event monitoring and OSG display of the live mode.  
9-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-39  
SHR-2040/2041/2042 USER’S MANUAL  
$ Recording  
- Rec. Mode  
It sets the Video Size, Quality, and Rate values during the recording by the  
setting the recoding ON/OFF for the related channel in the live mode.  
NTSC  
PAL  
15  
12.5  
12.5  
12.5  
15  
15  
15  
12.5  
Note  
Full D1(L) Video Size does not support 15ips, 10ips (NTSC) / 12.5ips, and  
8.33ips(PAL) Rate.  
- Video size Rec.  
Sets the Video size. The Video size being set in the menu affects to the ips  
setup of Rec. Mode and Event Rec.  
Note  
Full D1(L) Video Size does not support 15ips, 10ips (NTSC) / 12.5ips, and  
8.33ips(PAL) Rate.  
9-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-40  
- Event Rec.  
It sets the Video Size, Quality, Rate, Pre Alarm, and Post Alarm values to be  
recorded when an event occurs.  
NTSC  
PAL  
25  
25  
25  
25  
Note  
Full D1(L) Video Size does not support 15ips, 10ips(NTSC)/12.5ips, and 8.33ips(PAL)  
Rate.  
9-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-41  
SHR-2040/2041/2042 USER’S MANUAL  
- Alarm Rec.  
It sets the information necessary for the alarm recording.  
Note  
More than one camera should be selected to apply the alarm.  
- Motion Rec.  
It sets the information necessary for the recording by the motion Detection.  
9-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-42  
- Video Loss  
Video Loss sets up the information on how to inform the user of Video Loss of  
SHR-2040/2041/2042.  
% Network  
- Password  
It sets the password for Admin and User when connecting with  
SHR-2040/2041/2042 through the network in Smart Viewer.  
Caution  
- Network password should be composed of numeric and it can be input up to 8 digits.  
- If you leave password blank and apply it, a warning message pops up to ask your retyping.  
9-42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-43  
SHR-2040/2041/2042 USER’S MANUAL  
Note  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supported to the network password input.  
- Use the BACKSPACE key to delete the contents.  
Note  
- Default Admin Password is set to 654321.  
- Default User Password is set to 654321.  
- IP Settings  
It sets the network connection method of SHR-2040/2041/2042.  
SHR- SHR-2040/2041/2042 supports the connection with Static IP, Dynamic  
IP, and ADSL(PPPoE). It can set the network bandwidth. Adjust the  
bandwidth to the network condition in which SHR- SHR-2040/2041/2042 is  
connected.  
It sets the IP Address, Gateway, Subnet Mask, and DNS. Input both ID and  
password of the sub scriber for ADSL.  
Caution  
- Be sure to inquire the network manager before you input Network IP, Gateway,  
Subnet Mask, and DNS.  
- Both ADSL ID and Password can be input up to 40 digits of alphabets, numbers,  
and symbols without discrimination.  
9-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-44  
● Callback  
- You can set the Callback function of SHR-2040/2041/2042.  
- In the event of Alarm, Motion Detection, or Video Loss, set the IP address and  
port of PC where SmartViewer is installed to forward Callback messages. In  
failure of message forwarding, set the value for retrial.  
● Transfer Protocol  
- You can change the transfer protocol setting value. The protocol supports  
TCP/IP and UDP(Unicast, Multicast). Control Port(TCP/IP) and Port(UDP) to alter  
the connection port. Both Multicast IP and TTL are used for UDP(Multicast).  
9-44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-45  
SHR-2040/2041/2042 USER’S MANUAL  
Note  
- SHR-2040/2041/2042 uses 4 ports for TCP connection.  
- The PORT number is flexible and 4 consecutive numbers are grouped for the  
change ( 554,555,556,557 ● 558,559,560,561 )  
- If you use the IP Router for network composition, you should allocate a protocol  
for SHR-2040/2041/2042.  
Viewer Setup  
- Click the [Viewer Setup] for Viewer Setup.  
- Viewer Setup sets the various kinds of item related to the operation of Smart  
Viewer.  
- Viewer Setup is composed of 5 items; Video Recording, File Converting,  
Sequence Time, OSD Display, and Auto Connection.  
1
2
4
3
5
6
! Item to set the information necessary for saving the video data displayed into  
.dvr file when connecting with SHR-2040/2041/2042.  
*
@ Item to set the information necessary for converting the file saved  
in your PC with .dvr file into JPEG.  
*
# Item to set the information necessary for the auto sequence mode.  
$ Item to set the information of Smart Viewer OSD.  
% Item to set whether Smart Viewer shall be automatically connected to  
DVR(SHR-2040/2041/2042) or Site when it begins running.  
^ Item to set a port for the callback connection.  
9-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-46  
●
Video Recording  
! Naming  
- Being connected to SHR-2040/2041/2042 in the monitoring or search mode, you  
can save the video displayed with .dvr file and name it.  
*
- If you set to “Camera No. + Serial No.”, the file name depends on the camera  
number and serial number. If set to “Camera No. + Date”, it depends on the  
camera number, current date, and time.  
@ Location  
2040/2041/2042  
- When connecting with SHR-2040/2041/2042 in the monitoring or search mode  
and saving the video displayed, it sets the directory where .dvr file to be saved.  
*
- The current default directory is “Directory that installs Smart Viewer  
Program \ video \ dvr”.  
# Recording Time  
- When connecting with SHR-2040/2041/2042 in the monitoring or search mode  
and saving the video displayed, it sets the maximum saving time.  
- The saving time can be set from 1 to 10 minutes. If the saving time exceeds the  
preset time, the saving stops automatically.  
●
File Converting  
[JPEG]  
! Location  
2040/2041/2042  
- You can convert the file saved in your PC with .dvr format into JPEG file.  
*
The frames composing .dvr file will be converted into JPEG file.  
*
Sets the directory in which the converted JPEG file will be saved.  
- The current default directory is “Directory that installs Smart Viewer  
Program \ frame”.  
9-46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-47  
SHR-2040/2041/2042 USER’S MANUAL  
●
Sequence Time  
- When connecting with SHR-2040/2041/2042 in the monitoring mode, set the  
auto sequence time if the auto sequence is set. The time can be set from 10 to  
20 minutes.  
●
OSD Display  
- Sets if OSD shall be displayed on each channel of Smart Viewer.  
- Whether you check “Enable” or not, OSD will appear or not.  
However, Audio icon, PTZ icon, REC icon, and Alarm/Motion event icon will not  
be affected by the OSD condition.  
●
●
Callback Connection  
- Sets the port for Callback connection.  
Auto Connection  
- Sets if the smart viewer is automatically connected to SHR-2040/2041/2042 or  
site at the initial operation.  
- If you check “Auto Connection On”, the names of SHR-2040/2041/2042 and Site  
currently registered at the DVR/Site list will be displayed in the following list. If  
you select one from the list, the smart viewer will connect to the selected  
SHR-2040/2041/2042 or Site when it operates later.  
●
Language  
- Sets the language used in the SmartViewer.  
9-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-48  
Site Setup  
- Click the [Site Setup] button for Site Setup.  
- The information of DVR(SHR-2040/2041/2042) or Site that you want to connect by  
Smart Viewer is set in the Site Setup.  
- Smart Viewer allows you to connect with DVR(SHR-2040/2041/2042) or Site  
registered only here.  
1
3
5
2
4
! The DVR(SHR-2040/2041/2042) list that registered by the user is displayed.  
@ The button to add a new DVR(SHR-2040/2041/2042), delete, or edit the exist  
DVR(SHR-2040/2041/2042)  
# The site list that registered by the user is displayed.  
$ The button to add a new site, delete, edit the exist site, or delete  
DVR(SHR-2040/2041/2042) that composes the site.  
% The button to add DVR(SHR-2040/2041/2042) selected from the DVR list to the  
Site selected from the Site list. But, if the selected DVR(SHR-2040/2041/2042)  
is set to ADSL Network, it cannot be registered to the site.  
9-48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-49  
SHR-2040/2041/2042 USER’S MANUAL  
●
DVR List  
- The information of DVR(SHR-2040/2041/2042) that you want to connect by  
Smart Viewer is set in the DVR List.  
- You can register a new DVR(SHR-2040/2041/2042) or delete and edit the  
DVR(SHR-2040/2041/2042) selected from the registered list, and the name and  
IP / MAC Address of the registered DVR(SHR-2040/2041/2042) is displayed in  
DVR List.  
9-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-50  
! To add a new DVR(SHR-2040/2041/2042)  
- If you press the [New] button, the following window will pop up where you are  
able to add a new DVR(SHR-2040/2041/2042) information.  
1. Network Modes - LAN  
- If DVR(SHR-2040/2041/2042) is connected to the LAN, set the network mode  
to LAN.  
- If the LAN connected to DVR(SHR-2040/2041/2042) uses Static IP, select  
Static IP in the Address Type and input the name and IP address of  
DVR(SHR-2040/2041/2042).  
- You should select a PORT in accordance with the PORT number set at the  
DVR(SHR-2040/2041/2042) network menu.  
- If the Dynamic IP has been allocated for the ADSL that connected with  
DVR(SHR-2040/2041/2042) through the DHCP or PPPoE, select  
DHCP/ PPPoE in the Address Type and input the name and MAC address of  
DVR(SHR-2040/2041/2042).  
- You should select a PORT in accordance with the PORT number set at the  
DVR(SHR-2040/2041/2042) network menu.  
9-50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-51  
SHR-2040/2041/2042 USER’S MANUAL  
2.Network Modes - ADSL  
- If DVR(SHR-2040/2041/2042) is connected to the ADSL, set the network  
mode to ADSL.  
- If the ADSL connected to DVR(SHR-2040/2041/2042) uses Static IP, select  
Static IP in the Address Type and input the name and IP Address of  
DVR(SHR-2040/2041/2042).  
- You should select a PORT in accordance with the PORT number set at the  
DVR(SHR-2040/2041/2042) network menu.  
- If the Dynamic IP has been allocated for the LAN that connected with  
DVR(SHR-2040/2041/2042) through the DHCP, select DHCP in the Address  
Type and input the name and MAC address of DVR(SHR-2040/2041/2042).  
- You should select a PORT in accordance with the PORT number set at the  
DVR(SHR-2040/2041/2042) network menu.  
Note  
- DVR may be named in both English and Korean with the maximum 15 letters.  
- The login password should be same to the network password for SHR  
2040/2041/2042 to connect.  
- To add a new DVR, input all the information required.  
9-51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-52  
Note  
- The MAC address of DVR is written at the side label of the product.  
It is also found in the system information of DVR Menu.  
- If the DVR(SHR-2040/2041/2042) is connected to ADSL, the network bandwidth is  
low. Therefore, the transfer rate becomes low and the viewer operates in the more  
limited range.  
- The viewer can monitor up to 4CH all the same time.  
- The viewer can search or play only 1CH.  
- The audio does not play.  
- The number of playback frame is 0.5 ips in average, but it is variable depending on  
the number of channel and video size under simultaneous monitoring.  
@ Deletion of an old DVR(SHR-2040/2041/2042)  
- If you select a DVR(SHR-2040/2041/2042) in the DVR list for deletion and press  
the [Delete] button, the following message box pops up. Press the [OK] button to  
delete the DVR(SHR-2040/2041/2042).  
- When the DVR(SHR-2040/2041/2042) for deletion is connected with the Smart  
Viewer, the following message box pops up and the DVR(SHR-2040/2041/2042)  
cannot be deleted. Be sure to cut the connection between the  
DVR(SHR-2040/2041/2042) and the Smart Viewer before you delete it.  
9-52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-53  
SHR-2040/2041/2042 USER’S MANUAL  
# To Edit the old DVR(SHR-2040/2041/2042)  
- If you select a DVR(SHR-2040/2041/2042) in the DVR list to edit and press the  
[Edit] button, the following message box pops up. Press [OK] button to edit the  
DVR(SHR-2040/2041/2042).  
- When the DVR(SHR-2040/2041/2042) to edit is connected with the Smart  
Viewer, the following message box pops up and the DVR(SHR-2040/2041/2042)  
cannot be edited. Be sure to cut the connection between the  
DVR(SHR-2040/2041/2042) and the Smart Viewer before you edit it.  
9-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-54  
●
Site List  
- You can register and control the many DVRs(SHR-2040/2041/2042) to be  
connected with the smart viewer at once with a site in the site list. You are  
allowed to register a new site ,and delete or edit the selected site in the  
registered list. Also, you can add or delete a DVR(SHR-2040/2041/2042) to the  
site selected in the site list.  
- In the site list, both the name of a registered site and the name of  
DVR(SHR-2040/2041/2042) that composes the site are displayed with a list.  
A site can be composed of the maximum 9 DVRs(SHR-2040/2041/2042).  
! New site addition  
- If you press the [New] button, the following window pops up and you can  
allowed to input the information for a new site.  
- The information to be input is the site name.  
Note  
The site may be named in both English and Korean with the maximum 10 letters.  
9-54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-55  
SHR-2040/2041/2042 USER’S MANUAL  
@ To delete an old site or DVR(SHR-2040/2041/2042)  
- If you select a site or DVR(SHR-2040/2041/2042) in the site list for deletion  
and press the [Delete] button, the following message box pops up.  
Press the [OK] button to delete either site or DVR(SHR-2040/2041/2042).  
- When deleting the DVR(SHR-2040/2041/2042), it is deleted from the site  
composition but the DVR(SHR-2040/2041/2042) information is not deleted.  
- When the site to delete or the site that is composed of the DVR  
(SHR-2040/2041/2042) to delete is connected with the Smart Viewer, the  
following message box pops up and the site or the DVR  
(SHR-2040/2041/2042) cannot be deleted. Be sure to cut the connection  
between the DVR (SHR-2040/2041/2042) and the Smart Viewer before you  
delete it.  
# To edit the information of an old site  
- If you select a site in the site list to edit and press the [Edit] button, the  
following message box pops up and you can edit the site information.  
9-55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-56  
- When the site to edit is connected with the Smart Viewer, the following  
message box pops up and the site cannot be edited. Be sure to cut the  
connection between the DVR(SHR-2040/2041/2042) and the Smart Viewer  
before you edit it.  
- If you select a DVR(SHR-2040/2041/2042) and press the [Edit] button, the  
following message box pops up and the DVR(SHR-2040/2041/2042) cannot  
be edited. To edit the DVR(SHR-2040/2041/2042), go to the DVR list.  
●
To add a DVR(SHR-2040/2041/2042) to the site  
- If you press the [Add] button, the DVR(SHR-2040/2041/2042) selected in the  
DVR list is added to the site selected in the site list.  
The DVR(SHR-2040/2041/2042) set to ADSL cannot be added to the site.  
- You can add up to 4 DVRs(SHR-2040/2041/2042) to a site and the  
DVR(SHR-2040/2041/2042) composing the site can be deleted in the site list.  
- If you press the [Add] button unless a site is registered in the site list, a new site  
named “Site [0]” as a default is created and the DVR(SHR-2040/2041/2042) add  
to it.  
- When the site to add a DVR (SHR-2040/2041/2042) is connected with the Smart  
Viewer, the following message box pops up and the addition of  
DVR(SHR-2040/2041/2042) to the site is impossible. Be sure to cut the  
connection between the DVR(SHR-2040/2041/2042) and the Smart Viewer  
before you add a DVR(SHR-2040/2041/2042).  
9-56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-57  
SHR-2040/2041/2042 USER’S MANUAL  
S/W Version  
- If you press the [S/W Version] button, the smart viewer version, system require-  
ments, and the version of DVR(SHR-2040/2041/2042) System S/W, being connected  
to the smart viewer, are displayed.  
- You can upgrade the on-line DVR(SHR-2040/2041/2042) System S/W remotely. You  
are authorized with S/W upgrade in an Admin authority only. With the authority of  
user or without connecting with the DVR(SHR-2040/2041/2042), your access will be  
denied.  
1
2
! Displays the smart viewer version and system requirements.  
@ Displays the version and name of DVR if any DVR(SHR-2040/2041/2042) is  
being connected with the smart viewer. You are also able to upgrade remotely  
the on-line DVR(SHR-2040/2041/2042) S/W.  
9-57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-58  
●
Smart Viewer Version  
- Smart Viewer Version and system requirements are displayed.  
DVR Version  
●
SHR-2040/2041/2042  
- DVR Version not only displays the connected DVR(SHR-2040/2041/2042) name  
if any DVR(SHR-2040/2041/2042) is being connected with Smart Viewer or the  
name of DVR(SHR-2040/2041/2042) composing a site if any  
DVR(SHR-2040/2041/2042) is being connected with the site but also displays  
DVR(SHR-2040/2041/2042) S/W version.  
- When the smart viewer does not connected with the DVR(SHR-2040/2041/2042),  
it displayed with a gray and “Not connected” is displayed in the status.  
- Each DVR Version has a check box, which is used for S/W Upgrade.  
●
DVR(SHR-2040/2041/2042) S/W Upgrade  
- Smart Viewer upgrades on-line DVR(SHR-2040/2041/2042) S/W remotely.  
! Select a DVR(SHR-2040/2041/2042) to be upgraded among  
DVRs(SHR-2040/2041/2042) on line.  
SHR-2040/2041/2042  
9-58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-59  
SHR-2040/2041/2042 USER’S MANUAL  
@ Click the following button to open the “SHR-2040/2041/2042 Firmware” file  
in format.  
2040/2041/2042  
2040/2041/2042  
# Press the [Upgrade] button to transmit a file to the selected DVR(SHR-  
2040/2041/2042) and start the upgrade of DVR(SHR-2040/2041/2042) S/W.  
$ The progress of file transmission and upgrade is displayed at the bottom.  
Caution  
Be sure to suspend all the DVR system functions in action such as recording, MENU,  
backup, and playback before you upgrade the DVR(SHR-2040/2041/2042) S/W.  
Never try to turn the DVR(SHR-2040/2041/2042) power off during the S/W  
upgrade.  
The S/W upgrade requires about 5 minutes.  
If the S/W upgrade is suspended accidentally, the previous S/W will be left intact.  
Note  
The new Firmware necessary for DVR(SHR-2040/2041/2042) S/W upgrade should be  
downloaded from the CCTV Part in Products Section at the  
http://www.samsungelectronics.com.  
9-59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-60  
Ap p e n d ix  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-1  
SHR-4160N/P USER’S MANUAL  
Pro d u ct Sp e cifica tio n  
1
Item  
Details  
32bit RISC CPU  
Remarks  
CPU  
Memory  
SDRAM : 128MByte  
Flash : 16 MByte  
OS  
Embedded OS  
Broadcasting  
Input Voltage  
NTSC System  
2040-DC 12V, AC 110-220(NTSC),  
AC 110-230(PAL)  
2041/2042 - AC 110-220(NTSC)  
AC 100-230(PAL)  
Power Consumption  
2040 : 30Watt, 2041 : 60Watt, 2042 : 51Watt  
Composite 16 Channel  
- 1.0Vp-p  
Ω Hi Z Termination  
- 75  
Video Input  
BNC Type  
Loop Through Out 16 Channel  
- Auto Termination  
Composite 2 Channel  
- Normal Video Output 1 Channel  
- Spot Output 1 Channel  
- BNC Type  
Video  
Video Output  
S-Video 1 Channel  
- 1.0Vp-p  
VGA 1 Channel  
Mono 4 Channel  
Ω
Audio Input  
- -5dBm, 600  
RCA Type  
Audio  
Mono 1 Channel  
- -6dBm  
Audio Output  
RCA Type  
Video size  
Frame Rate (1Ch/4Ch)  
Video size &  
Frame Rate  
720X480 (NTSC)  
720X576 (PAL)  
30fps/480fps(NTSC)  
/25fps/576fps(PAL)  
Live  
Single  
Monitoring  
Display Mode  
4 Split  
Mode sequence  
Freeze  
2 X Zoom  
10-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-2  
Item  
Details  
Remarks  
Compression  
Method  
Video : MPEG4  
Audio : ADPCM  
Resolution  
Quality Level  
Max Image Rate  
Very High  
High  
Standard  
Low  
15ips(NTSC)/  
25(PAL)  
CIF(C)  
352X240(NTSC)  
/352X288(PAL)  
Video Size &  
Performance  
Very High  
High  
Standard  
Low  
Half D1(N)  
15ips(NTSC)/  
12.5(PAL)  
720X288(NTSC)  
/720X288(PAL)  
Recording  
Very High  
High  
Standard  
Low  
30ips(NTSC)/  
25ips(PAL)  
Full D1(L)  
720X480(NTSC)  
/720X576(PAL)  
●
Normal  
REC Key  
PANIC Key  
Schedule Table  
●
Emergency  
●
Schedule  
Event  
Recording  
Mode  
-Alarm Detection  
-Motion Detection  
-Video Loss  
-Pre & Post Recording  
Time Laps  
Internal  
NTSC : 1ips/3ips/5ips/7.5ips/10ips/15ips  
PAL : 1ips/2.5ips/5ips/6.25ips/8.33ips/12.5ips/25ips  
* Packing  
120GB  
(Samsung)  
x 1EA  
ATA HDD x 2(MAX)  
-Primary/Secondary IDE Connector  
-MAX HDD Size : 250GB x 2 = 500Giga Byte  
Storage  
Capacity  
USB HDD  
-MAX 1 (Not support USB hub)  
-MAX HDD Size : 250GB  
External  
10-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-3  
SHR-2040/2041/2042 USER’S MANUAL  
Item  
Details  
Remarks  
Calendar  
Event  
- Normal, Schedule, Alarm, Motion, Video Loss  
Search Mode  
Date/Time  
Go to First  
Go to Last  
Backup Data  
Decoding Performance  
Video size  
1Ch  
4Ch  
Play Back Video size &  
Performance  
CIF  
30ips(NTSC)/25ips(PAL  
)
30ips(NTSC)/25ips(PAL)/1CH  
Half D1(N) 15ips(NTSC)/12.5ips(PAL) 15ips(NTSC)/12.5ips(PAL)/1CH  
Full D1(L) 30ips(NTSC)/25ips(PAL) 30ips(NTSC)/25ips(PAL)/1CH  
Full D1 is supported in the 1 ch mode only  
●
●
●
Single  
4 Split  
PIP  
1Channel Decoding  
4Channel Decoding  
1Channel Decoding + 1Channel Live  
Display Mode  
●
6 Split PB(Single)+4 Channel Live  
●
●
●
- Single 6 Split(1CH PB) PIP 4 Split  
●
9 Split  
PB(4 Split)+4 Channel Live  
●
●
- 4 Split 6 Split(4CH PB) 4 Split  
Play, Pause, Stop, 2x Digital Zoom  
Fast Forward/Fast Reverse  
- 2x, 4x, 8x, 16x, 32x, 64x  
Play Mode  
Backup  
USB External HDD  
USB CD/DVD Writer  
USB Flash Memory  
Input : 4 Input  
- 5mA  
Output : 2 Relay Output  
- 2A/30VDC, 0.5A/125VAC  
Reset : 1 Input  
- 5mA  
Alarm  
Network  
Serial I/F  
Ethernet : 10/100 Base T, ADSL(PPPoE), DHCP  
●
RS-485  
PTZ Device Control, Remote Control Device  
CPU : Pentium III, 1GHz or higher  
RAM : SDRAM 256MB or higher  
Graphic Accelerator : Graphic Memory  
32MB or higher  
DirectX : 8.1 or higher  
PC Spec.  
Remote  
Support OS  
Viewer  
Win98se, WinME, Win2000, WinXP  
Live Image Monitoring Mode  
Local File Search & Play Back Mode  
Remote File Search & Play Back Mode  
Same as Remote Viewer  
Function  
PC Spec.  
Support OS  
Win2000, WinXP  
Backup device(External HDD, USB Memory, CD/DVD)  
search and replay mode  
Backup  
Viewer  
Function  
Operation Temp.  
Preservation Temp.  
Operation Humidity  
Preservation Humidity  
Size  
0ºC ~ 40ºC  
-20ºC ~ 60ºC  
20% ~ 85% RH  
20% ~ 85% RH  
215(W) X 88(H) X 337(D) (2040)  
430(W) X 88(H) X 400(D) (2041/2042)  
About 3.35Kg(2040)/About 6.5Kg(2041)/About 7.3Kg(2042)  
Weight  
10-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-4  
Th e sp e cifica tio n o f HDD a n d p e rip h e ra l d e vice  
2
●
Internal ATA HDD/IEEE1394/USB HDD I/F External HDD  
Maker RPM Capactity Interface Buffer Series Name Model No  
Samsung 5,400  
Remark  
SV12.03N  
SV1604N  
6Y120LO  
6Y160LO  
5A250JO  
WD1200LB  
WD1600LB  
Attached model in shipment  
120 GB  
160 GB  
120 GB  
160 GB  
250 GB  
120 GB  
160 GB  
2MB SpinPoint V80  
DiamondMax  
Ultra ATA-133  
Ultra ATA-133  
7,200  
7,200  
5,400  
Plus 9  
2MB  
Maxtor  
MaxLine II  
Western  
Digital  
EIDE  
7,200  
WD Prpte ‘ge’  
2MB  
●
USB I/F CD-RW, DVD-RW Drive  
Maker  
RPM  
Disk  
Remark  
CD-R  
CD-RW  
CD-R  
CD-RW  
DVD+R  
DVD-R  
DVD+RW  
PX-W5232TU  
Plextor  
SONY  
Liteon  
PX-708UF  
DRX-700UL  
●
DVD-RW is not supported.  
SHOW-1633SX  
●
Internal ATA HDD/IEEE1394/USB HDD I/F External HDD  
Remark  
Maker  
P & C  
Model  
FDISK V2  
ActiveDrive  
CellDisk  
IOCELL  
Stormblue  
ALTech  
Bayon  
SanDisk  
PNY  
MICRO X  
AnyDrive  
Extreme USB Flash disk  
cruzer mini  
Attache  
GeekSquad  
Lexar  
Jump Drive  
10-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-5  
SHR-2040/2041/2042 USER’S MANUAL  
O u tlin e Dra w in g s  
3
[SHR-2040]  
[SHR-2041]  
10-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-6  
[SHR-2042]  
10-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-7  
SHR-2040/2041/2042 USER’S MANUAL  
Fa cto ry De fa u lt  
4
This restores the Network information and preset values in SHR-2040/2041/2042 to  
the original state at the time of factory shipment.  
Factory Default will be done as follows;  
- Use System / Load Factory Default in MENU or,  
- If you hold on to the Mode button in Live Mode and keep pressing the CH5  
button for 5 seconds, the system will return to the Factory default condition.  
The front button repeats the flickering.  
Classification  
System Setup  
Detailed Items  
Date Format  
Factory Setup  
YYYY-MM-DD  
Time Format  
Language  
Summer Time  
Password  
Password Lock  
Disk End Mode  
Disk End Beep  
Video  
24 Hours  
Time/Date/Language  
English  
Off  
4321  
Password  
On  
Stop  
HDD Mode  
Off  
On  
Audio  
On  
Camera Config  
Title  
CAM_01 ~ CAM_4  
Auto Seq.  
ID  
5 sec  
Camera No.  
Protocol  
Baudrate  
Parity  
None  
9600  
Camera Setup  
None  
PTZ Device  
Data  
8
Stop  
1
Serial Mode  
Brightness  
Contrast  
Color  
Half Duplex  
50  
50  
50  
Screen Setup  
10-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-8  
Classification  
Monitoring  
Detailed Items  
Factory Setup  
Duration  
Date  
Off  
Event Monitoring  
OSD Display  
On  
Time  
On  
Title  
On  
Status  
On  
Spot Out Channel  
CH1  
Spot Out Event Monitor  
Monitor Out  
Off  
Composite Out  
1CH DVR Support  
Mode  
Off  
On  
Record Mode  
Setup  
Video Size  
CIF  
Quality  
Normal  
Rate  
30ips(NTSC)/25ips(PAL)  
Continuous Recording  
Event Recording  
Off  
On  
Record Schedule  
Video Size  
CIF  
Video Size  
Rate  
Normal  
30ips(NTSC)/25ips(PAL)  
Off  
Event Record Mode  
PreEvent  
PostEvent  
Sensor State  
Camera  
Off  
Off  
Alarm  
Camera No.  
None  
Event Record  
Setup  
Detection Setup  
Alarm-Out  
Beep-Out  
M.D State  
Area  
10 sec  
Off  
All Area  
High  
Motion Detection Setup  
Video Loss Detection Setup  
Sensitivity  
Alarm-Out  
Beep-Out  
Video Loss Detection Setup  
Alarm-Out  
Beep-Out  
None  
10 sec  
Off  
None  
10 sec  
10-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-9  
SHR-2040/2041/2042 USER’S MANUAL  
SHR-2 0 4 0 / 2 0 4 1 / 2 0 4 2 Sm a rt Vie w e r  
5
Fra m e Sp e cifica tio n fo r th e Pla y b a ck  
NTSC  
FRAME  
Viewer Screen  
Split Mode  
VIDEO SIZE  
RATE  
15  
Half D1(N)  
1 frame/sec  
15 frame/sec  
15 frame/sec  
Half D1(N)  
CIF (C)  
Nine-split  
Fore-split  
Single  
15 frame/sec  
15 frame/sec  
15 frame/sec  
CIF (C)  
Nine-split  
Fore-split  
Single  
10 frame/sec  
10 frame/sec  
10 frame/sec  
Half D1(N)  
10 frame/sec  
10 frame/sec  
10 frame/sec  
CIF (C)  
10  
Nine-split  
Fore-split  
Single  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
Half D1(N)  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
CIF (C)  
7.5  
Nine-split  
Fore-split  
Single  
5 frame/sec  
5 frame/sec  
5 frame/sec  
Half D1(N)  
5 frame/sec  
5 frame/sec  
5 frame/sec  
CIF (C)  
5
3
Nine-split  
Fore-split  
Single  
3 frame/sec  
3 frame/sec  
3 frame/sec  
Half D1(N)  
3 frame/sec  
3 frame/sec  
3 frame/sec  
CIF (C)  
Nine-split  
Fore-split  
Single  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1
10-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-10  
PAL  
FRAME  
RATE  
Viewer Screen  
Split Mode  
VIDEO SIZE  
Half D1(N)  
1 frame/sec  
12.5 frame/sec  
12.5 frame/sec  
Half D1(N)  
CIF (C)  
Nine-split  
Fore-split  
Single  
12.5 frame/sec  
12.5 frame/sec  
12.5 frame/sec  
CIF (C)  
12.5  
8.33  
6.25  
Nine-split  
Fore-split  
Single  
8.33 frame/sec  
8.33 frame/sec  
8.33 frame/sec  
Half D1(N)  
8.33 frame/sec  
8.33 frame/sec  
8.33 frame/sec  
CIF (C)  
Nine-split  
Fore-split  
Single  
6.25 frame/sec  
6.25 frame/sec  
6.25 frame/sec  
Half D1(N)  
6.25 frame/sec  
6.25 frame/sec  
6.25 frame/sec  
CIF (C)  
Nine-split  
Fore-split  
Single  
5 frame/sec  
5 frame/sec  
5 frame/sec  
Half D1(N)  
5 frame/sec  
5 frame/sec  
5 frame/sec  
CIF (C)  
5
Nine-split  
Fore-split  
Single  
2.5 frame/sec  
2.5 frame/sec  
2.5 frame/sec  
Half D1(N)  
2.5 frame/sec  
2.5 frame/sec  
2.5 frame/sec  
CIF (C)  
2.5  
Nine-split  
Fore-split  
Single  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1
Note  
The play frame specification of Smart Viewer varies on the setup of SHR-4160N/P  
Recording Rate and Video Size or the screen split mode of Smart Viewer. The above  
specification is applicable only when the main body of SHR-4160N/P is connected  
with a fast network like LAN. When the main body of SHR-4160N/P is connected  
with a slow network like ADSL, the play speed will be 0.5 Frame/sec. In addition,  
the above specification has been defined to the recommended specification of your  
PC. If your PC specification is lower than the recommended, the number of frame to  
played may diminish.  
10-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-11  
SHR-2040/2041/2042 USER’S MANUAL  
Tro u b le sh o o tin g (FAQ )  
6
1. The system power is dead and LED in front of the system does not operate at all.  
- Please check the power connection.  
- Check the power voltage.  
- If all your efforts like above end up with nothing, check or exchange the power  
supply.  
2. Video data remains in the system but some channels displays no video data but  
turns all blue.  
- Check the image of the camera connected to the system. Improper input of  
camera input may cause this symptom.  
- Check the camera power supply.  
- Sometimes, you see this symptom when the video data is connected with  
multisystems and the video signal from the video data distributor in use feels  
weak. If it’s the case, you shall connect the camera images with  
SHR-2040/2041/2042 DVR directly to check or improve such a symptom.  
3. The REC button in front has no effect on turning on REC LED or recording process.  
- Please check the HDD space.  
- Please check the Record Mode setup in MENU. It should be Off.  
4. All the front LEDs are in operation but the monitor remains black.  
- Video out may come out differently with the connected monitor. In short, Video  
Out is set to Composite Output but connected to VGA Input Monitor or vice  
versa. Then, keep pressing both the "MODE" button and the "0" button on the left  
for 5 seconds until LED lights on in the order of 1.2.3.4.5 to change the Video  
Out mode.  
5. The front LED blinks and the logo screen repeatedly appears.  
- This symptom may be resulted from failure of HDD connection inside  
SHR-2040/2041/2042 DVR. Take off the cover and check HDD connection  
status. If HDD connection has no problem, please consult with the shop where  
you bought SHR-2040/2041/2042 DVR.  
6. You cannot enter MENU by forgotten password.  
- If you forget the password, you shall reset SHR-2040/2041/2042 DVR to the  
values set at the factory. Keep pressing both the "MODE" button and the "5"  
button on the left for 5 seconds until LED lights on in the order of 1●2●3●4●5  
The password default is "4321".  
10-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-12  
7. The channel button does not operate in Live.  
- If the current screen is Event Monitoring, the channel button does not operate.  
Then, press the Alarm button to terminate the current screen and select a channel.  
8. The cursor cannot reach Start during Calendar Search.  
- Please check both the channel and the date for play are left checked. Both shall  
be checked for play with Start. The cursor cannot reach the unrecorded date.  
9. Alarm, once issued, keeps being issued though you press the front Alarm button  
for cancellation.  
- Press the front Menu button to cancel Alarm as follows.  
1) To cancel Event Monitoring Screen : Monitoring- Event Monitoring Duration Off  
2) To cancel Buzzer : Event Record-Alarm (Motion Detection/Video Loss).  
Alarm-Out.  
3) To cancel Event : Event Record-Alarm (Motion Detection/Video Loss).  
State Off.  
10. Pressing the PTZ button in Live receives no response.  
- Check the Protocol and other setup values through Menu●Camera●PTZ  
Device match with the PTZ camera.  
11. When you connect several IEEE1394 armored HDDs to SHR-2040/2041/2042  
DVR through Menu, SHR-2040/2041/2042 DVR cannot recognize all the HDDs.  
- It requires time to recognize several armored HDDs. Please try again in a few  
minutes. If retrial makes no improvement, HDD could be abnormal. Please  
exchange the HDD.  
12. You cannot connect to SHR-2040/2041/2042 DVR through Smart View.  
- Check if 3 Smart Viewer users are in connection with SHR-2040/2041/2042 DVR.  
SHR-2040/2041/2042 DVR allows no more than 3 users’ connection with  
Smart Viewer at a time.  
- Check the Network setup of SHR-2040/2041/2042 DVR.  
- Check Network cable connection.  
- When you use DHCP/ADSL(PPPoE) for connection, please check if you get the  
right SHR-2040/2041/2042 DVR MAC Address.  
- If SHR-2040/2041/2042 DVR is connected to the ADSL network, please check if  
Bandwidth is set below 600 Kbps. If the Bandwidth for ADSL is set to high, the  
connection with Smart Viewer may be instable due to the heavy network load as  
the ADSL speed is low.  
10-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-13  
SHR-2040/2041/2042 USER’S MANUAL  
13. Smart Viewer in operation is disconnected.  
- If you change time, network setup, HDD format, Default Setup, or HDD  
attachment or detachment for SHR-2040/2041/2042 DVR, the current Smart  
Viewer will be automatically disconnected.  
- Check network connection. Smart Viewer, if disconnected from Network, will try  
reconnection up to 5 times. If it remains unconnected after 5 time trial, it will  
automatically give up connection.  
- As far as SHR-2040/2041/2042 DVR is connected to the ADSL network, you may  
be disconnected from Smart Viewer when the network conditions goes bad.  
14. The Audio icon of Smart Viewer is left inactivated in the Live mode. Setting Audio  
to On in the Camera menu of SHR-2040/2041/2042 DVR will make no difference.  
- If your PC has no Audio driver or has some problem with Audio play of an Audio  
driver, the Audio icon will be inactivated. Please check Audio driver installation  
status.  
15. When selecting the channel which PTZ Camera is connected to in the Live mode  
of Smart Viewer, click the "Menu Control" button among PTZ setup buttons to  
enter the Function Menu mode in PTZ Camera, and return from the other channel,  
the PTZ related buttons have been initialized.  
- PTZ control is available in both Smart Viewer and SHR-2040/2041/2042 DVR.  
Other user might control PTZ for SHR-2040/2041/2042 DVR to terminate the  
PTZ Camera Menu or Auto Pan/Scan/Pattern motions while you select the other  
channel. This may cause the initialization.  
16. No Time Bar in the Search  
- Time Line can be converted into 2 modes, General(24 Hour Display) and  
Extension(2 Hour Display). In the Extension mode, Time Bar may not be seen in  
the current time. Please enter the General mode or click the LEFT or RIGHT  
button to search Time Bar.  
10-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-1 2005.6.29 2:36 PM Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-14  
Correct Disposal of This Product  
(Waste Electrical & Electronic Equipment)  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking shown on the product or its literature, indicates that it should not be disposed with other  
household wastes at the end of its working life. To prevent possible harm to the environment or human  
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it  
responsibly to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased this product, or their local  
government office, for details of where and how they can take this item for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract.  
This product should not be mixed with other commercial wastes for disposal.  
AB68-00517B  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pyramid Car Audio Car Stereo System TLM606NC User Guide
Radio Shack Cordless Telephone 43 3537 User Guide
Ricoh Digital Camera 15530 User Guide
Rinnai Water Heater REU VA3237W User Guide
Royal Sovereign Laminator RSL2701S User Guide
Ryobi Trimmer 130rEB User Guide
Samsung Automobile Parts SGH P777 User Guide
Samsung Satellite TV System ANT1400 User Guide
Sanyo Battery Charger UPF383456L User Guide
Sceptre Technologies Computer Monitor E22 User Guide